Loading manual…
Seagate Standard models (ST8000VN002) user manual
- Type
- User manual
- Language
- English
- Pages
- 39
- Category
- Storage & drives
- Models
- ST1000VN002ST2000VN003ST2000VN004ST3000VN006ST3000VN007ST4000VN006ST4000VN008ST6000VN001ST6000VN006ST8000VN002
Open PDFOpens the file on objects.icecat.biz.
Contents
- SATA Product Manualp. 1
- Seagate® Technology Support Servicesp. 6
- 1.0 Introductionp. 7
This manual describes the functional, mechanical and interface specifications for the following: Seagate® IronWolfTM model drives These drives provide the…
- 1.1 About the SATA interfacep. 8
The Serial ATA (SATA) interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: • Easy installation…
- 2.0 Drive Specificationsp. 9
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this…
- 2.1 Specification summary tablesp. 9
The specifications listed in Table 1 are for quick reference. For details on specification measurement or definition, refer to the appropriate section of this…
- 2.2 Formatted capacityp. 12
*One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating…
- 2.3 Default logical geometryp. 13
Cylinders: 16,383 • Read/write heads: 16 • Sectors per track: 63 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively…
- 2.4 Start/stop timesp. 13
The start/stop times listed below are for all models. Time-to-ready may be longer than normal if the drive power is removed without going through normal OS…
- 2.5 Power specificationsp. 14
The drive receives DC power (+5V or +12V) through a native SATA power connector. Refer to Figure 3 on page 24. 2.5.1 Power consumption Power requirements for…
- 2.6 Environmental limitsp. 18
Temperature and humidity values experienced by the drive must be such that condensation does not occur on any drive part. Altitude and atmospheric pressure…
- 2.7 Acousticsp. 20
Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound…
- 2.8 Electromagnetic immunityp. 20
When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency…
- 2.9 Reliabilityp. 21
2.9.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) The production disk drive shall achieve an annualized failure-rate of 0.87% (MTBF of…
- 2.10 HDD and SSD Regulatory Compliance and Safetyp. 21
For the latest regulatory and compliance information see: www.seagate.com/support/ scroll down the page to the Compliance, Safety and Disposal Guide link.…
- 2.11 Corrosive environmentp. 21
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous…
- 2.12 Reference documentsp. 22
Supported standards Serial ATA Revision 3.3 specification ANSI Documents SFF-8301 3.5” Drive Form Factor with Serial Connector INCITS 522-2014 SCSI Protocol…
- 2.13 Product warrantyp. 22
Beginning on the date of shipment to the customer and continuing for the period specified in the purchase contract, Seagate warrants that each product…
- 2.14 Seagate® Rescue™ Data Recovery Servicep. 23
If you suffer a data loss event within the Seagate Rescue Data Recovery warranty period, and you are eligible to participate in and submit a case under the…
- 3.0 Configuring and Mounting the Drivep. 25
This section contains the specifications and instructions for configuring and mounting the drive
- 3.1 Handling and static-discharge precautionsp. 25
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following…
- 3.2 Configuring the drivep. 25
Each drive on the SATA interface connects point-to-point with the SATA host adapter. There is no master/slave relationship because each drive is considered a…
- 3.3 SATA cables and connectorsp. 25
The SATA interface cable consists of four conductors in two differential pairs, plus three ground connections. The cable size may be 30 to 26 AWG with a…
- 3.4 Drive mountingp. 26
Users can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. Refer to Figure 4…
- 4.0 SATA Interfacep. 30
These drives use the industry-standard Serial ATA (SATA) interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0 to…
- 4.1 Hot-Plug compatibilityp. 30
IronWolf drives incorporate connectors which enable users to hot plug these drives in accordance with the SATA Revision 3.2 specification. This specification…
- 4.2 SATA device plug connector pin definitionsp. 30
Table 11 summarizes the signals on the SATA interface and power connectors. Notes 1. All pins are in a single row, with a 1.27 mm (0.050 in) pitch. 2. The…
- 4.3 Supported ATA commandsp. 31
The following table lists SATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA International…