Loading manual…
Seagate Standard model (ST8000VN0022) user manual
- Type
- User manual
- Language
- English
- Pages
- 41
- Category
- Storage & drives
- Models
- ST1000VN002ST2000VN004ST3000VN007ST4000VN008ST6000VN0033ST8000VN0022
Open PDFOpens the file on objects.icecat.biz.
Contents
- SATA Product Manualp. 1
- Seagate® Technology Support Servicesp. 6
- 1.0 Introductionp. 7
This manual describes the functional, mechanical and interface specifications for the following: Seagate® IronWolfTM model drives: These drives provide the…
- 1.1 About the SATA interfacep. 8
The Serial ATA (SATA) interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: • Easy installation…
- 2.0 Drive Specificationsp. 9
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this…
- 2.1 Specification summary tablesp. 9
The specifications listed in Table 1 are for quick reference. For details on specification measurement or definition, refer to the appropriate section of this…
- 2.2 Formatted capacityp. 13
*One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating…
- 2.3 Default logical geometryp. 13
Cylinders: 16,383 • Read/write heads: 16 • Sectors per track: 63 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively…
- 2.4 Seek timep. 13
Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table…
- 2.5 Start/stop timesp. 14
The start/stop times listed below are for all models. Time-to-ready may be longer than normal if the drive power is removed without going through normal OS…
- 2.6 Power specificationsp. 14
The drive receives DC power (+5V or +12V) through a native SATA power connector. Refer to Figure 3 on page 25. 2.6.1 Power consumption Power requirements for…
- 2.7 Environmental specificationsp. 17
This section provides the temperature, humidity, shock, and vibration specifications for NAS HDDs. This section provides the temperature, humidity, shock, and…
- 2.8 Acousticsp. 20
Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound…
- 2.9 Electromagnetic immunityp. 20
When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency…
- 2.10 Reliability - Mean Time Between Failurep. 21
The product will achieve a Mean Time Between Failure Rate (MTBF) of 1,000,000 hours when operated in an environment of ambient air temperatures of 25°C.…
- 2.11 Warrantyp. 21
To determine the warranty for a specific drive, use a web browser to access the following web page: http://www.seagate.com/support/warranty-and-replacements/…
- 2.12 Agency and Safety Certificationsp. 22
Each Hard Drive and Solid State Drive ("drives") has a product label that includes certifications that are applicable to that specific drive. The following…
- 2.13 Environmental protectionp. 24
Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.13.1…
- 2.14 Corrosive environmentp. 25
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous…
- 3.0 Configuring and Mounting the Drivep. 26
This section contains the specifications and instructions for configuring and mounting the drive
- 3.1 Handling and static-discharge precautionsp. 26
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following…
- 3.2 Configuring the drivep. 26
Each drive on the SATA interface connects point-to-point with the SATA host adapter. There is no master/slave relationship because each drive is considered a…
- 3.3 SATA cables and connectorsp. 26
The SATA interface cable consists of four conductors in two differential pairs, plus three ground connections. The cable size may be 30 to 26 AWG with a…
- 3.4 Drive mountingp. 27
Users can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. Refer to Figure 4…
- 4.0 SATA Interfacep. 32
These drives use the industry-standard Serial ATA (SATA) interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0 to…
- 4.1 Hot-Plug compatibilityp. 32
IronWolf drives incorporate connectors which enable users to hot plug these drives in accordance with the SATA Revision 3.2 specification. This specification…
- 4.2 SATA device plug connector pin definitionsp. 32
Table 11 summarizes the signals on the SATA interface and power connectors. Notes 1. All pins are in a single row, with a 1.27 mm (0.050 in) pitch. 2. The…
- 4.3 Supported ATA commandsp. 33
The following table lists SATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA International…