Loading manual…
Seagate ST2000VN003 user manual
- Type
- User manual
- Language
- English
- Pages
- 31
- Category
- Storage & drives
- Models
- ST10000VN000ST1000VN008ST2000VN003ST6000VN006
Open PDFOpens the file on objects.icecat.biz.
Contents
- SATA Product Manualp. 1
- Seagate® Technology Support Servicesp. 5
- 1.0 Introductionp. 6
This manual describes the functional, mechanical and interface specifications for the following: Seagate® IronWolf® Serial ATA model drives:: These drives…
- 1.1 About the Serial ATA interfacep. 6
The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: • Easy installation and…
- 2.0 Drive specificationsp. 7
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this…
- 2.1 Specification summary tablesp. 7
The specifications listed in the following tables are for quick reference. For details on specification measurement or definition, see the appropriate section…
- 2.2 Formatted capacityp. 9
Seagate IronWolf Serial ATA Product Manual, Rev. B (Draft 2) 8 2.2Formatted capacity * One GB equals one billion bytes when referring to hard drive capacity.…
- 2.3 Recording and interface technologyp. 9
2.4 Start/stop times Power-on to ready time is based on typical operating conditions, default full current spin-up profile, and clean shutdown prior to…
- 2.4 Start/stop timesp. 9
Power-on to ready time is based on typical operating conditions, default full current spin-up profile, and clean shutdown prior to measurement. To ensure a…
- 2.5 Power specificationsp. 10
The drive receives DC power (+5V or +12V) through a native SATA power connector. See Figure 3 on page 20. 2.5.1 Power consumption Power requirements for the…
- 2.6 Environmental limitsp. 14
Temperature and humidity values experienced by the drive must be such that condensation does not occur on any drive part. Altitude and atmospheric pressure…
- 2.7 Acousticsp. 16
Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound…
- 2.8 Test for Prominent Discrete Tones (PDTs)p. 16
Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing.…
- 2.9 Electromagnetic immunityp. 16
When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency…
- 2.10 Reliabilityp. 17
2.10.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) The production disk drive shall achieve an annualized failure-rate of 0.87% (MTBF of…
- 2.11 HDD and SSD Regulatory Compliance and Safetyp. 17
For the latest regulatory and compliance information see: www.seagate.com/support/ scroll down the page to the Compliance, Safety and Disposal Guide link.…
- 2.12 Corrosive environmentp. 17
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous…
- 2.14 Reference documentsp. 18
Supported standards Serial ATA Revision 3.3 specification ANSI Documents SFF-8301 3.5” Drive Form Factor with Serial Connector INCITS 522-2014 SCSI Protocol…
- 2.15 Product warrantyp. 18
Beginning on the date of shipment to the customer and continuing for the period specified in the purchase contract, Seagate warrants that each product…
- 2.16 Seagate® Rescue™ Data Recovery Servicep. 19
If you suffer a data loss event within the Seagate Rescue Data Recovery warranty period, and you are eligible to participate in and submit a case under the…
- 3.0 Configuring and mounting the drivep. 21
This section contains the specifications and instructions for configuring and mounting the drive
- 3.1 Handling and static-discharge precautionsp. 21
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following…
- 3.2 Configuring the drivep. 21
Each drive on the Serial ATA interface connects point-to-point with the Serial ATA host adapter. There is no master/slave relationship because each drive is…
- 3.3 Serial ATA cables and connectorsp. 21
The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connections. The cable size may be 30 to 26 AWG with a…
- 3.4 Drive mountingp. 22
Users can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 4 for drive…
- 4.0 Serial ATA (SATA) interfacep. 23
These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/ output (PIO) modes 0–4…
- 4.1 Hot-Plug compatibilityp. 23
IronWolf Serial ATA drives incorporate connectors which enable users to hot plug these drives in accordance with the Serial ATA Revision 3.2 specification.…
- 4.2 Serial ATA device plug connector pin definitionsp. 23
Table 5 summarizes the signals on the Serial ATA interface and power connectors. Notes: 1. All pins are in a single row, with a 1.27mm (0.050”) pitch. 2. The…
- 4.3 Supported ATA commandsp. 24
The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA: High…