D-Link 20-Port Gigabit Stackable Smart Managed Switch including 2 x 10G SFP+ & 2 x SFP (DGS-1510-20) user manual

Contents

1. 1. Introductionp. 9

   This manual’s command descriptions are based on the software release 1.30. The commands listed here are the subset of commands that are supported by the…

2. 2. Web-based Switch Configurationp. 11

   Management Options Connecting using the Web User Interface Logging onto the Web Manager Smart Wizard Web User Interface (Web UI) Management Options The Switch…

3. 3. Systemp. 17

   Device Information System Information Settings Peripheral Settings Port Configuration PoE (DGS-1510-28P and DGS-1510-28XMP Only) System Log Time and SNTP Time…

4. 4. Managementp. 37

   User Account Settings Password Encryption Login Method SNMP RMON Telnet/Web Session Timeout DHCP DNS NTP IP Source Interface File System Physical Stacking…

5. 5. Layer 2 Featuresp. 91

   FDB VLAN Spanning Tree ERPS (G.8032) Loopback Detection Link Aggregation L2 Multicast Control LLDP FDB Static FDB Unicast Static FDB This window is used to…

6. 6. Layer 3 Featuresp. 149

   ARP Gratuitous ARP UDP Helper UDP Helper IP Forward Protocol This window is used to view and configure the IP helper forwarding on ports. To view the following…

7. 7. Quality of Service (QoS)p. 163

   Basic Settings Advanced Settings Basic Settings Port Default CoS This window is used to view and configure the port’s default CoS settings. To view the…

8. 8. Access Control List (ACL)p. 181

   ACL Configuration Wizard ACL Access List ACL Interface Access Group ACL VLAN Access Map ACL VLAN Filter ACL Configuration Wizard This window is used to guide…

9. 9. Securityp. 280

   Port Security 802.1X AAA RADIUS TACACS IMPB DHCP Server Screening ARP Spoofing Prevention BPDU Attack Protection MAC Authentication Web-based Access Control…

10. 10. OAMp. 354

    Cable Diagnostics DDM Cable Diagnostics The cable diagnostics feature is designed primarily for administrators or customer service representatives to verify…

11. 11. Monitoringp. 360

    Utilization Statistics Mirror Settings sFlow Device Environment Utilization Port Utilization This window is used to display the percentage of the total…

12. 12. Greenp. 371

    Power Saving EEE Power Saving This window is used to configure the power saving settings of the Switch. To view the following window, click Green > Power…

13. 13. Save and Toolsp. 374

    Save Configuration Firmware Upgrade & Backup Configuration Restore & Backup Log Backup Ping Trace Route Language Management Reset Reboot System Save…

14. Appendix A - System Log Entriesp. 386

    The following table lists all possible entries and their corresponding meanings that will appear in the System Log of this switch. 802.1X Log Description…

15. Appendix B - Trap Entriesp. 411

    The following table lists all possible trap log entries and their corresponding meanings that will appear in the switch. 802.1X Trap Name Description OID…

16. Appendix C - RADIUS Attributes Assignmentp. 421

    The RADIUS Attributes Assignment on the DGS-1510 is used in the following modules: Console, Telnet, SSH, Web, 802.1X, MAC-based Access Control, JWAC, and WAC.…

17. Appendix D - IETF RADIUS Attributes Supportp. 424

    Remote Authentication Dial-In User Service (RADIUS) attributes carry specific authentication, authorization, information and configuration details for the…

18. Appendix E - ERPS Informationp. 426

    Only hardware-based ERPS (external PHY) supports the fast link drop interrupt feature with a recovery time of 50ms. Model Name ERPS Port 1 to 8 Port 9 to 16…

Other documents for this model

• Epson D-Link 28-Port Gigabit Stackable Smart Managed Switch including 4 x 10G SFP+ (DGS-1510-28X) user manual
• Epson D-Link 28-Port Gigabit Stackable Smart Managed Switch including 4 x 10G SFP+ (DGS-1510-28X) user manual
• Epson D-Link 28-Port Gigabit Stackable Smart Managed Switch including 4 x 10G SFP+ (DGS-1510-28X) installation instructions