Epson D-Link 28-Port Gigabit Stackable Smart Managed Switch including 4 x 10G SFP+ (DGS-1510-28X) user manual

Contents

1. 1. Introductionp. 5

   This manual’s command descriptions are based on the software release 1.81. The commands listed here are the subset of commands that are supported by the…

2. 2. Basic CLI Commandsp. 14

   2-1 help This command is used to display a brief description of the help system. Use the help command in any command mode. help Parameters None. Default None.…

3. 3. 802.1X Commandsp. 29

   3-1 clear dot1x counters This command is used to clear 802.1X counters (diagnostics, statistics and session statistics). clear dot1x counters {all | interface…

4. 4. Access Control List (ACL) Commandsp. 42

   4-1 access-list resequence This command is used to re-sequence the sequence number of the access list entries in an access list. Use the no form of this…

5. 5. Access Management Commandsp. 71

   5-1 access class This command is used to specify an access list to restrict the access via a line. Use the no form of this command to remove the specified…

6. 6. ARP Spoofing Prevention Commandsp. 96

   6-1 ip arp spoofing-prevention This command is used to configure an ARP Spoofing Prevention (ASP) entry of the gateway used for preventing ARP poisoning…

7. 7. Asymmetric VLAN Commandsp. 99

   7-1 asymmetric-vlan This command is used to enable the asymmetric VLAN function. Use the no form of this command to disable the asymmetric VLAN function.…

8. 8. Authentication, Authorization, and Accounting (AAA) Commandsp. 100

   8-1 aaa accounting commands This command is used to configure the method list used for all commands at the specified privilege level. Use the no form of this…

9. 9. Basic IPv4 Commandsp. 130

   9-1 arp This command is used to add a static entry in the Address Resolution Protocol (ARP) cache. Use the no form of this command to remove a static entry in…

10. 10. Basic IPv6 Commandsp. 137

    10-1 clear ipv6 neighbors This command is used to clear IPv6 neighbor cache dynamic entries. clear ipv6 neighbors {all | interface INTERFACE-ID} Parameters all…

11. 11. BPDU Attack Protection Commandsp. 150

    11-1 spanning-tree bpdu-protection (global) This command is used to enable the Bridge Protocol Data Unit (BPDU) Protection function globally. Use the no form…

12. 12. Cable Diagnostics Commandsp. 154

    12-1 test cable-diagnostics This command is used to start the cable diagnostics to test the status and length of copper cables. test cable-diagnostics…

13. 13. Command Logging Commandsp. 157

    13-1 command logging enable This command is used to enable the command logging function. Use the no form of this command to disable the command logging…

14. 14. Debug Commandsp. 158

    14-1 debug reboot on-error This command is used to set the Switch to reboot when a fatal error occurs. Use the no form of this command to set the Switch not to…

15. 15. DHCP Auto-Configuration Commandsp. 166

    15-1 autoconfig enable This command is used to enable the auto-configuration function. Use the no form of this command to disable the auto-configuration…

16. 16. DHCP Client Commandsp. 168

    16-1 ip dhcp client class-id This command is used to specify the vendor class identifier used as the value of Option 60 for the DHCP discover message. Use the…

17. 17. DHCP Relay Commandsp. 171

    17-1 class (DHCP Relay) This command is used to enter the DHCP pool configuration mode and associate a range of IP addresses with the DHCP class. Use the no…

18. 18. DHCP Server Commandsp. 197

    18-1 address range This command is used to specify an IP address range to be associated with a DHCP class in a DHCP address pool. Use the no form of this…

19. 19. DHCP Snooping Commandsp. 221

    19-1 ip dhcp snooping This command is used to globally enable DHCP snooping. Use the no form of this command to disable DHCP snooping. ip dhcp snooping no ip…

20. 20. DHCPv6 Client Commandsp. 240

    20-1 clear ipv6 dhcp client This command is used to restart the DHCPv6 client on an interface. clear ipv6 dhcp client INTERFACE-ID Parameters INTERFACE-ID…

21. 21. DHCPv6 Guard Commandsp. 242

    21-1 ipv6 dhcp guard policy This command is used to create or modify a DHCPv6 guard policy, and enter the DHCPv6 Guard Configuration Mode. Use the no form of…

22. 22. DHCPv6 Relay Commandsp. 246

    22-1 ipv6 dhcp relay destination This command is used to enable the DHCP for IPv6 relay service on the interface and specify a destination address to which…

23. 23. DHCPv6 Server Commandsp. 252

    23-1 address prefix This command is used to specify an address prefix for address assignment. Use the no form of this command to remove the address prefix.…

24. 24. Digital Diagnostics Monitoring (DDM) Commandsp. 268

    24-1 show interfaces transceiver This command is used to display the current transceiver module operating parameters. show interfaces [INTERFACE-ID [, | -]]…

25. 25. D-Link Discovery Protocol (DDP) Client Commandsp. 277

    25-1 ddp This command is used to enable DDP client function globally or on the specified ports. Use the no form of this command to disable DDP client. ddp no…

26. 26. Domain Name System (DNS) Commandsp. 280

    26-1 clear host This command is used to clear the dynamically learned host entries in the privileged user mode. clear host {all | [HOST-NAME]} Parameters all…

27. 27. DoS Prevention Commandsp. 285

    27-1 dos-prevention This command is used to enable and configure the DoS prevention mechanism. Use the no form of this command to reset DoS prevention to the…

28. 28. Dynamic ARP Inspection Commandsp. 289

    28-1 arp access-list This command is used to create or modify an ARP access list. This command will enter into the ARP access-list configuration mode. Use the…

29. 29. Error Recovery Commandsp. 302

    29-1 errdisable recovery This command is used to enable the error recovery for causes and to configure the recovery interval. Use the no form of this command…

30. 30. Ethernet Ring Protection Switching (ERPS) Commandsp. 305

    For more information, refer to Appendix E - ERPS Information. 30-1 description This command is used to configure the description for Ethernet Ring Protection…

Other documents for this model

• Epson D-Link 28-Port Gigabit Stackable Smart Managed Switch including 4 x 10G SFP+ (DGS-1510-28X) user manual
• Epson D-Link 28-Port Gigabit Stackable Smart Managed Switch including 4 x 10G SFP+ (DGS-1510-28X) installation instructions