APC Maintenance Bypass Panel (GVSBPSU20K60H) user manual

Contents

1. Important Safety Instructions — SAVE THESE INSTRUCTIONSp. 5

   Read these instructions carefully and look at the equipment to become familiar with it before trying to install, operate, service or maintain it. The following…

2. Electromagnetic Compatibilityp. 6

   NOTICE RISK OF ELECTROMAGNETIC DISTURBANCE This is a product category C2 UPS product. In a residential environment, this product may cause radio inference, in…

3. Safety Precautionsp. 6

   DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Read all instructions in the installation manual before installing or working on this product. Failure…

4. Specificationsp. 10

   NOTE: Maximum short circuit rating: 10 kA RMS symmetrical. NOTE: GVSBPSU80K120H can support a load of up to 120 kW/kVA as long as the neutral current (250 A)…

5. Recommended Upstream Protectionp. 10

   Refer to the UPS installation manual for recommended upstream protection

6. Recommended Cable Sizesp. 10

   DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH All wiring must comply with all applicable national and/or electrical codes. The maximum allowable…

7. Torque Specificationsp. 10
8. Maintenance Bypass Panel Shipping Weights and Dimensionsp. 11
9. Maintenance Bypass Panel Weights and Dimensionsp. 11
10. Clearancep. 11

    NOTE: Clearance dimensions are published for airflow and service access only. Consult with the local safety codes and standards for additional requirements in…

11. Environmentp. 12

    Operating Storage Temperature 0 °C to 40 °C -25 °C to 55 °C Relative humidity 5-95% non-condensing 10-80% non-condensing Elevation 0-3000 m Protection class…

12. Compliancep. 12

    Safety IEC 62040-1: 2017, Edition 2.0, Uninterruptible Power Systems (UPS) - Part 1: Safety requirements Performance IEC 62040-3: 2011-03, 2nd edition…

13. One Line Diagramsp. 13

    NOTE: In Schneider Electric literature, 'disconnect device' is used as a generic term covering circuit breakers or switches as their position may vary…

14. Installation Procedure for Galaxy VS UPSp. 16

    Single System – Single Mains Simplified 1+1 Parallel System – Single Mains Single System – Dual Mains Simplified 1+1 Parallel System – Dual Mains 1. Mount the…

15. Installation Procedure for Easy UPS 3S, Easy UPS 3S Pro, and Easy UPS 3Mp. 18

    Single System – Single Mains Single System – Dual Mains 1. Mount the Maintenance Bypass Panel to the Wall, page 19. 2. Prepare the Maintenance Bypass Panel for…

16. Mount the Maintenance Bypass Panel to the Wallp. 19

    CAUTION RISK OF INJURY OR EQUIPMENT DAMAGE • Mount the maintenance bypass panel to a wall or a rack that is structurally sound and able to support the weight…

17. Prepare the Maintenance Bypass Panel for Cablesp. 21

    DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Do not drill or punch holes with the gland plates installed and do not drill or punch holes in close…

18. Remove the Neutral Jumpersp. 22

    NOTE: The neutral jumper makes a bolted connection of the neutral so that the neutral is not disconnected when the 4-pole disconnect devices are opened. NOTE…

19. Connect the Power Cables for a 3:3 UPS Systemp. 23

    NOTE: For a simplified 1+1 parallel system, install the power cables from the two UPSs on the front and rear side of the busbar using the same bolt. 1. Connect…

20. Connect the Power Cables for a 3:1 UPS Systemp. 27

    1. Connect the PE cables to the PE busbar. GVSBPSU20K60H and GVSBPSU80K120H 2. Do one of the following: – For single mains: Connect the input cables from…

21. Connect the Signal Cables for Galaxy VS UPS – Single Systemp. 29

    NOTE: Route the signal cables separately from the power cables and route the Class 2/SELV cables separately from the non-Class 2/non-SELV cables. GVSBPSU10K20H…

22. Connect the Signal Cables for Galaxy VS UPS – Simplified 1+1 Parallel Systemp. 32

    NOTE: The disconnect device indicator lights are supplied by UPS 1 and will only work while UPS 1 is powered. NOTE: The AUX switches are in optional parallel…

23. Connect the Signal Cables for Easy UPS 3S, Easy UPS 3S Pro, and Easy UPS 3M – Single Systemp. 39

    1. Remove the three disconnect device indicator lights and the disconnect device indicator light labels from the maintenance bypass panel. The disconnect…

24. Add Translated Safety Labels to Your Productp. 42

    The safety labels on your product are in English and French. Sheets with translated safety labels are provided with your product. 1. Find the sheets with…

25. Final Installationp. 43

    1. Close the inner door and fasten it with the screws. 2. Add labels to the disconnect device indicator lamps, the disconnect devices, and the diagram label…

26. Decommission or Move the Maintenance Bypass Panel to a New Locationp. 44

    1. Shut down the UPS completely – follow the instructions in the UPS operation manual. 2. Lockout/Tagout all disconnect devices in the switchgear in the OFF…

Other documents for this model

• APC Maintenance Bypass Panel (GVSBPSU10K20H) user manual