MSI Optix MEG381CQR PLUS user manual

Contents

1. Getting Startedp. 3

   This chapter provides you with the information on hardware setup procedures. While connecting devices, be careful in holding the devices and use a grounded…

2. Installing the Monitor Standp. 4

   1. Leave the monitor in its protective foam packaging. Align the stand bracket to the monitor groove. Tighten the stand bracket with screws. 2. Connect the…

3. Adjusting the Monitorp. 5

   This monitor is designed to maximize your viewing comfort with its adjustment capabilities. ⚠ ⚠Important Avoid touching the display panel when adjusting the…

4. Monitor Overviewp. 6
5. Connecting the Monitor to PCp. 8

   1. Turn off your computer. 2. Connect the video cable from the monitor to your computer. 3. Connect the power cord to the monitor power jack. (Figure A) 4.…

6. OSD Setupp. 9

   This chapter provides you with essential information on OSD Setup. ⚠ ⚠Important All information is subject to change without prior notice

7. Navi Keyp. 9

   The monitor comes with a Navi Key, a multi-directional control that helps navigate the On-Screen Display (OSD) menu. Up/Down/Left/Right: •selecting function…

8. Hot Keyp. 9

   Users may enter into preset function menus by moving the Navi Key up, down, left or right when the OSD menu is inactive. •Users may customize their own Hot…

9. OSD Menusp. 10

   Gaming 1st Level Menu 2nd/3rd Level Menu Description Mode User •Use Up or Down Button to select and preview mode effects. •Press the Middle Button to confirm…

10. Gamingp. 10

    1st Level Menu 2nd/3rd Level Menu Description Mode User •Use Up or Down Button to select and preview mode effects. •Press the Middle Button to confirm and…

11. G-SYNC® Processorp. 12

    1st Level Menu 2nd Level Menu Description G-SYNC Esports OFF •Before turning on G-SYNC, users need to connect a G-SYNC capable graphics card to the G-SYNC…

12. Imagep. 13

    1st Level Menu 2nd/3rd Level Menu Description Peak White (nits) 40-500 •Peak White will be grayed out when HDR or HDCR are enabled. Contrast 0-100 •Default is…

13. Input Sourcep. 14

    1st Level Menu 2nd Level Menu Description DP •Input Source scan sequence: DP > HDMI1 > HDMI2. HDMI1 HDMI2 Auto Scan OFF •Users can use the

14. Navi Keyp. 14

    to select Input Source at below status: • While “Auto Scan” is set to “OFF” with the monitor at power saving mode; • While “No Signal” message box is shown on…

15. Settingp. 15

    1st Level Menu 2nd Level Menu Description Language 繁體中文 •Users have to press the Middle Button to confirm and apply the Language setting. •Language is an…

16. Specificationsp. 16

    Monitor Optix MEG381CQR Plus Size 37.5 inch Curvature 2300R Panel Type IPS Resolution 3840 x 1600 Aspect Ratio 21:9 Brightness (nits) 450 Contrast Ratio 1000:1…

17. Preset Display Modesp. 18
18. Troubleshootingp. 19

    The power LED is off. • Press the monitor power button again. • Check if the monitor power cable is properly connected. No image. • Check if the computer…

19. Safety Instructionsp. 20

    Read the safety instructions carefully and thoroughly. •All cautions and warnings on the device or User Guide should be noted. •Refer servicing to qualified…

20. TÜV Rheinland Certificationp. 22

    TÜV Rheinland Low Blue Light Certification Blue light has been shown to cause eye fatigue and discomfort. MSI now offers monitors with TÜV Rheinland Low Blue…

21. Regulatory Noticesp. 23

    CE Conformity This device complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to…