Loading manual…
Loading manual…
GETTING READY 5 1 •Main parts The appearance of the machine differs depending on the model. 1 Bobbin winding thread guide and pretension disk (page 13) 2…
may differ from the table below depending on the machine model you purchased. For more details on included accessories and their part codes of your machine…
The following are available as optional accessories to be purchased separately. Attaching the stitch pattern plate (For models equipped with the stitch pattern…
GETTING READY 9 1 a Make sure that the machine is turned off (the main power switch is set to “ ”), and then plug the power cord into the power supply jack on…
When the machine is turned on, the LCD will light up and the following screen is displayed. To change the displayed settings, use the operation keys and stitch…
GETTING READY 11 1 •Changing the needle stop position The needle position when stitching is finished can be changed from the down position to the up position.…
Winding the bobbin This section describes how to wind thread onto a bobbin. a Place the bobbin on the bobbin winder shaft so that the notch in the bobbin…
This section describes how to wind thread onto a bobbin. a Place the bobbin on the bobbin winder shaft so that the notch in the bobbin aligns with the spring…
l Slide the sewing speed controller to desired sewing speed position. m Remove the spool for the bobbin thread from the spool pin. Installing the bobbin…
GETTING READY 15 1 h While lightly holding down the bobbin with your right hand (1), guide the thread through the slit in the needle plate cover (2) and…
When threading the upper thread, carefully follow the instructions. a Turn on the machine. b Raise the presser foot lever to raise the presser foot. Memo • By…
If the threads will be pulled to create gathers or the thread at the beginning of sewing will be finished, for example, when free motion quilting, first pull…
GETTING READY 19 1 • Needles that can be used with this machine: Home sewing machine needles (size 65/9 - 100/16) * The larger the number, the larger the…
Checking the needle Before using the needle, place the flat side of the needle on a flat surface and check that the distance between the needle and the flat…
Before using the needle, place the flat side of the needle on a flat surface and check that the distance between the needle and the flat surface is even
GETTING READY 21 1 Replacing the presser foot a Press (Needle position button) once or twice to raise the needle. b Turn off the machine. c Raise the presser…
a Prepare the appropriate needle and thread for the type of fabric. (page 19) If necessary, replace the needle. (page 20) b Wind thread onto a bobbin, and then…
Reverse/reinforcement stitches are generally necessary at the beginning and end of sewing. With reinforcement stitches, 3 to 5 stitches are sewn at the same…
When reinforcement priority is turned on, reinforcement stitches will be sewn at the beginning and/or end of sewing a reinforcement stitch pattern, even if…
SEWING BASICS 2 Reinforcement priority When reinforcement priority is turned on, reinforcement stitches will be sewn at the beginning and/or end of sewing a…
•Upper thread is too tight If the bobbin thread is visible from the right side of the fabric, the upper thread is too tight. Loosen the thread tension. Turn…
To sew an even seam, start sewing so that the seam allowance is to the right of the presser foot, and the edge of the fabric is aligned with either the right…
Sewing thick fabrics If the fabric does not fit under the presser foot The presser foot lever can be raised to two different positions. If the fabric does not…
Fabric When sewing on stretch fabrics, lightweight fabrics, or fabrics with coarse weaves, attach stabilizer on the wrong side of the fabric. An alternative…
VARIOUS STITCHES 3 •Utility stitches *1 Twin needle can be used by attaching zigzag foot “J”. (page 33 to 36) *2 When using the twin needle, set the stitch…
Overcasting Stitches Sew overcasting stitches along the edges of cut fabric to prevent them from fraying. •Using overcasting foot “G” a Attach overcasting foot…