Loading manual…
TP-Link T1600G-52TS (TL-SG2452) user manual
- Type
- User manual
- Language
- English
- Pages
- 285
- Category
- Network switches
- Models
- SG2424SG2452T1600G-52TS
Open PDFOpens the file on objects.icecat.biz.
Contents
- Prefacep. 16
This Guide is intended for network administrator to provide referenced information about CLI (Command Line Interface). The device mentioned in this Guide…
- Chapter 1 Using the CLIp. 19
1.1 Accessing the CLI You can log on to the switch and access the CLI by logging on to the switch remotely by a Telnet or SSH connection through an Ethernet…
- Chapter 2 User Interfacep. 30
2.1 enable Description The enable command is used to access Privileged EXEC Mode from User EXEC Mode. Syntax enable Command Mode User EXEC Mode Example If you…
- Chapter 3 IEEE 802.1Q VLAN Commandsp. 36
VLAN (Virtual Local Area Network) technology is developed for the switch to divide the LAN into multiple logical LANs flexibly. Hosts in the same VLAN can…
- Chapter 4 MAC-based VLAN Commandsp. 41
MAC VLAN (Virtual Local Area Network) is the way to classify the VLANs based on MAC Address. A MAC address is relative to a single VLAN ID. The untagged…
- Chapter 5 Protocol VLAN Commandsp. 44
Protocol-based VLAN (Virtual Local Area Network) is the way to classify VLANs based on Protocols. A Protocol corresponds to a VLAN ID. The untagged packets and…
- Chapter 6 Voice VLAN Commandsp. 48
Voice VLANs are configured specially for voice data stream. By configuring Voice VLANs and adding the ports with voice devices attached to voice VLANs, you can…
- Chapter 7 Etherchannel Commandsp. 54
Etherchannel Commands are used to configure LAG and LACP function. LAG (Link Aggregation Group) is to combine a number of ports together to make a single…
- Chapter 8 User Management Commandsp. 60
User Manage Commands are used to manage the user’s logging information by Web, Telnet or SSH, so as to protect the settings of the switch from being randomly…
- Chapter 9 HTTP and HTTPS Commandsp. 67
With the help of HTTP (HyperText Transfer Protocol) or HTTPS (Hyper Text Transfer Protocol over Secure Socket Layer), you can manage the switch through a…
- Chapter 10 Binding Table Commandsp. 75
You can bind the IP address, MAC address, VLAN and the connected Port number of the Host together, which can be the condition for the ARP Inspection to filter…
- Chapter 11 ARP Inspection Commandsp. 84
ARP (Address Resolution Protocol) Detect function is to protect the switch from the ARP cheating, such as the Network Gateway Spoofing and Man-In-The-Middle…
- Chapter 12 DoS Defend Commandsp. 89
DoS (Denial of Service) Attack is to occupy the network bandwidth maliciously by the network attackers or the evil programs sending a lot of service requests…
- Chapter 13 System Log Commandsp. 91
The log information will record the settings and operation of the switch respectively for you to monitor operation status and diagnose malfunction. 13.1…
- Chapter 14 SSH Commandsp. 99
SSH (Security Shell) can provide the unsecured remote management with security and powerful authentication to ensure the security of the management…
- Chapter 15 IEEE 802.1X Commandsp. 104
IEEE 802.1X function is to provide an access control for LAN ports via the authentication. Only the supplicant passing the authentication can access the LAN.…
- Chapter 16 MAC Address Commandsp. 115
MAC Address configuration can improve the network security by configuring the Port Security and maintaining the address information by managing the Address…
- Chapter 17 System Configuration Commandsp. 122
System Commands can be used to configure the System information and System IP, reboot and reset the switch, upgrade the switch system and other operations.…
- Chapter 18 IPv6 Address Configuration Commandsp. 142
The IPv6 address configuration commands are provided in the Interface Configuration Mode, which includes the routed port, the LAG and the VLAN interface. Enter…
- Chapter 19 Ethernet Configuration Commandsp. 147
Ethernet Configuration Commands can be used to configure the Bandwidth Control, Negotiation Mode and Storm Control for Ethernet ports. 19.1 interface…
- Chapter 20 QoS Commandsp. 157
QoS (Quality of Service) function is used to optimize the network performance. It provides you with network service experience of a better quality. 20.1 qos…
- Chapter 21 Port Mirror Commandsp. 165
Port Mirror refers to the process of forwarding copies of packets from one port to a monitoring port. Usually, the monitoring port is connected to data…
- Chapter 22 Port Isolation Commandsp. 168
Port Isolation provides a method of restricting traffic flow to improve the network security by forbidding the port to forward packets to the ports that are…
- Chapter 23 Loopback Detection Commandsp. 170
With loopback detection feature enabled, the switch can detect loops using loopback detection packets. When a loop is detected, the switch will display an…
- Chapter 24 ACL Commandsp. 175
24.1 access-list create Description The access-list create command is used to create standard-IP ACL and extend-IP ACL. Syntax access-list create…
- Chapter 25 PoE Commandsp. 183
Note: Only T1600G-28PS and T1600G-52PS support PoE function. PoE (Power over Ethernet) technology describes a system to transmit electrical power along with…
- Chapter 26 MSTP Commandsp. 195
MSTP (Multiple Spanning Tree Protocol), compatible with both STP and RSTP and subject to IEEE 802.1s, can disbranch a ring network. STP is to block redundant…
- Chapter 27 IGMP Snooping Commandsp. 212
IGMP Snooping (Internet Group Management Protocol Snooping) is a multicast control mechanism running on Layer 2 switch. It can effectively prevent multicast…
- Chapter 28 MLD Snooping Commandsp. 229
MLD Snooping (Multicast Listener Discovery Snooping) is a multicast control mechanism running on Layer 2 switch. It can effectively prevent multicast groups…
- Chapter 29 SNMP Commandsp. 245
SNMP (Simple Network Management Protocol) functions are used to manage the network devices for a smooth communication, which can facilitate the network…