Loading manual…
Loading manual…
WARNING: Use of control, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or…
Maintenance: • To protect your display from possible damage, do not put excessive pressure on the display. • Unplug the display if you are not going to use it…
Read and follow these instructions when connecting and using your display: • Unplug the display if you are not going to use it for an extensive period of time.…
Remote Controller Precautions: • This product requires remote switch (ON/OFF) from Front Side ; the Back Side only has OSD function operated by remote…
Disconnect devices: • For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. Important Safety…
Please make sure you have a solid installation. (Locks on the ground) As shown in the picture. You can install Dual-sided display by screws x10 (M6x20mm)…
IPC installation: • Dual-sided display (DF-55) contains a metal plat, it is used to fix your IPC. • The relative position of the screw holes is shown below.…
IPC installation: 1 Tear down the IPC fixed sheet metal first 2 Set & fix the IPC & Reinstall the IPC fixed sheet metal By screws x 4 (M3x6.5mm) IPC01 Set &…
• This product is packed in a carton, together with the standard accessories. • Due to the size and weight of this display it is recommended for two people to…
Package 2 Package Content 10
Dual-Sided Display (upside part : DF-55 dual set) Power Cord x1 Remote Controller x1 (Battery : CR 2025 3V) Dual-Sided Display (downside part : Bottom housing)…
Full Size Stand (with wheels) M10x100mm screw x4 Package Content 12
Front View Back View Top View Side View Package Content 2.3 Over View 13
1. Display (Dual-sided) 2. Display Set 3. Remote control sensor (Dual-sided) 4. Stand (with use hole x 10 ) 5. User Door (with locker) 1 2 4 5 3 Package…
Putting the down half part upside , and tear down the downside covers. screws x 20 (M3x6mm) Setting Up The Display 3.1 Step1 : Tear down the downside covers 15
Don’t put anything on the crossbar when you set up it. Notice: The upside part front side have a Product Label. When you place the upside part into the…
Place the upside part into downside part screws x 2 (M5x30mm) screws x 8 (M4x8mm) M5x30mm screw x 1 (front) M4x8mm screw x 4 (front, back) Setting Up The…
LVDS 24V LVDS LVDS Connector 14pin 12pin 12pin 14pin 24V Connector Setting Up The Display 3.3 Step3 : Connect the LVDS and 24V 18
Reinstall the downside covers screws x 20 (M3x6mm) Setting Up The Display 3.4 Step4 : Reinstall the downside covers 19
HDMI*2 AC Switch HDMI Back Side(700 nits) Front Side(700 nits) Setting Up The Display 3.5 Step5 : Open the user door, Connect by HDMI connector & AC switch…
Install the Full Size Stand (DF-55) screws x10 (M6x20mm) 1 Setting Up The Display 3.6 DF-55 Full Size Stand installation 21
Useing screws to secure the DF-55 on the ground screwsx4(M10x100mm) Fixed Wheel (You can fix the wheel by this Brakes) Setting Up The Display 22
• The dimensions of Counterweight mounting position : 487*416*26.5mm • Use M8 mounting screws x4 • Suggestion : the counterweight diameter of this working…
Notice: This product requires remote switch (ON/OFF) from Front Side. (The Front Side have a user door) No. Key Descriptions Power Power on/Power off Menu Into…
Luminance Press MENU to select one of the following, and then press “UP” or “DOWN” to select the desired level, ---Brightness1: Range: 0~100 ; Default: : 100…
Color Press MENU to select one of the following, and then press “UP” or “DOWN” to select the desired level, ---Color Temperature: Range: 6500K, 9300K, 11500K…
Press “MENU” into the OSD Setting Menu, and then press “UP” or “DOWN” to select the item, at last press “EXIT” to leave menu : OSD Settings Press MENU to…