TP-Link 16-Port 10/100 Mbps + 2-Port Gigabit Rackmount PoE Switch (TL-SL1218P) installation instructions

Contents

1. Chapter 1 Introductionp. 5

   1.1 Product Overview TL-SL1218P, TL-SL1218MP, and TL-SL1226P are Power Sourcing Equipment (PSE*) which require no configurations. The 10/100 Mbps RJ45 ports on…

2. 1.1 Product Overviewp. 5

   TL-SL1218P, TL-SL1218MP, and TL-SL1226P are Power Sourcing Equipment (PSE*) which require no configurations. The 10/100 Mbps RJ45 ports on the switch support…

3. 1.2 Appearancep. 5

   Front Panel The front panels of TL-SL1218P and TL-SL1218MP are shown as the following figure. Figure 1-1 Front Panel of TL-SL1218P 10/100 Mbps RJ45 Port (Port…

4. Chapter 2 Installationp. 10

   2.1 Package Contents Make sure that the package contains the following items. If any of the listed items is damaged or missing, contact your distributor. One…

5. 2.1 Package Contentsp. 10

   Make sure that the package contains the following items. If any of the listed items is damaged or missing, contact your distributor. One Power Cord One Switch…

6. 2.2 Safety Precautionsp. 10

   To avoid any device damage and bodily injury caused by improper use, you should observe the following rules. • • Safety Precautions • •Keep the power off…

7. 2.3 Installation Toolsp. 12

   Phillips screwdriver • •ESD-preventive wrist wrap • •Cables Note: These tools are not included with our product. If needed, you can purchase them separately

8. 2.4 Product Installationp. 12

   Desktop Installation To install the device on the desktop, follow the steps: 1. Set the device on a flat surface which is strong enough to support the entire…

9. Chapter 3 Connectionp. 14

   3.1 Ethernet Port Connect an Ethernet port of the switch to the computer by RJ45 cable as the following figure shows. Figure 3-1 Connecting the RJ45 Port RJ45…

10. 3.1 Ethernet Portp. 14

    Connect an Ethernet port of the switch to the computer by RJ45 cable as the following figure shows. Figure 3-1 Connecting the RJ45 Port RJ45 Port RJ45 Cable

11. 3.2 SFP Portp. 14

    The following figure demonstrates the connection of SFP port to an SFP module. Figure 3-2 Inserting the SFP Module SFP Slot SFP Module

12. 3.3 Verify Installationp. 14

    After completing the installation, please verify the following items: • •There should be 5 to 10 cm of clearance around the device for ventilation and make…

13. 3.4 Power Onp. 15

    Plug the negative connector of the provided power cord into the power socket of the device and plug the positive connector into a power outlet as the following…

14. 3.5 Initializationp. 15

    After the device is powered on, it begins the Power-On Self-Test. A series of tests run automatically to ensure the device functions properly. During this…

15. Appendix A Troubleshootingp. 16

    Unmanaged PoE/PoE+ Switch Appendix A Troubleshooting Q1. Why is the PWR LED not lit? The PWR LED should be lit when the power system is working normally. If…

16. Appendix B Specificationsp. 17

    Unmanaged PoE/PoE+ Switch Appendix B Specifications Item Content Standard IEEE802.3i, 802.3u, 802.3ab, 802.3z, 802.3af, 802.3at, 802.3x Protocol CSMA/CD…

Other documents for this model

• TP-Link 24-Port 10/100Mbps + 2-Port Gigabit Unmanaged PoE+ Switch (TL-SL1226P V1) installation instructions