Loading manual…
Loading manual…
Thank you for purchasing a new motherboard from MSI®. This Quick Start section provides demonstration diagrams about how to install your computer. Some of the…
CPU •Supports AMD Ryzen™ 5000 Series, 5000 G-Series, 4000 G-Series, and 3000 Series processors •Supports Socket AM4 * Please go to www.msi.com to get the…
MSI Center Features •MSI AI Engine •Cooling Wizard •Mystic Light •Ambient Link •Frozr AI Cooling •Hardware Monitoring •Live Update •MSI Companion •System…
Item Description 1 Flash BIOS button - Please refer to page 50 for details about updating BIOS with Flash BIOS button. 2 DisplayPort 3 1Gbps LAN (RJ45) port 4…
Speed LED Link/ Activity LED Link/ Activity LED Speed LED Status Description Status Speed Off No link Off 10Mbps Yellow blinking slowly Linked Green 100Mbps…
Audio jacks to headphone and microphone diagram Audio jacks to stereo speakers diagram AUDIO INPUT LAN Port LED Status Table Speed LED Link/ Activity LED Link/…
1. Screw two antenna cables tight to the Wi-Fi antenna connectors as shown. 2. Place the antenna as high as possible.
Introduction to the AM4 CPU The surface of the AM4 CPU has a yellow triangle to assist in correctly lining up the CPU for motherboard placement. The yellow…
⚠Important •If you install a large and heavy graphics card, you need to use a tool such as MSI Gaming Series Graphics Card Bolster to support its weight to…
These connectors are SATA 6Gb/s interface ports. Each connector can connect to one SATA device. ⚠Important •Please do not fold the SATA cable at a 90-degree…
M2_1 M2_2 Installing M.2 module into M2_1 slot 1. Loosen the screws of M.2 Shield Frozr heatsink. 2. Lift the M.2 Shield Frozr heatsink up and remove it. 1 1 2
This connector allows you to connect audio jacks on the front panel. 1 2 10 9 Pin Signal Name Pin Signal Name 1 MIC L 2 Ground 3 MIC R 4 NC 5 Head Phone R 6…
These connectors allow you to connect an ATX power supply. CPU_PWR1 Pin Signal Name Pin Signal Name 1 Ground 2 Ground 3 Ground 4 Ground 5 +12V 6 +12V 7 +12V 8…
This connector allows you to connect the chassis intrusion switch cable. Normal (default) Trigger the chassis intrusion event Using chassis intrusion detector…
This connector allows you to connect USB 5Gbps ports on the front panel. ⚠Important Note that the Power and Ground pins must be connected correctly to avoid…
These connectors allow you to connect USB 2.0 ports on the front panel. ⚠Important •Note that the VCC and Ground pins must be connected correctly to avoid…
Fan connectors can be classified as PWM (Pulse Width Modulation) Mode or DC Mode. PWM Mode fan connectors provide constant 12V output and adjust fan speed with…
This connector allows you to connect the optional serial port with bracket. 1 2 10 9 Pin Signal Name Pin Signal Name 1 DCD 2 SIN 3 SOUT 4 DTR 5 Ground 6 DSR 7…
There is CMOS memory onboard that is external powered from a battery located on the motherboard to save system configuration data. If you want to clear the…
The JRAINBOW connectors allow you to connect the WS2812B Individually Addressable RGB LED strips 5V. JRAINBOW connector JRAINBOW connector System Fan connector…
LED_SW1: EZ LED Control This switch is used to switch on/ off all the LEDs of motherboard. LED_OFF LED_ON (Default) CPU - indicates CPU is not detected or…
These LEDs indicate the debug status of the motherboard. Onboard LEDs
This switch is used to switch on/ off all the LEDs of motherboard. LED_OFF LED_ON (Default) CPU - indicates CPU is not detected or fail. DRAM - indicates DRAM…
Please download and update the latest utilities and drivers at www.msi.com Installing Windows 11 1. Power on the computer. 2. Insert the Windows 11…
is an application that helps you easily optimize game settings and smoothly use content creation softwares. It also allows you to control and synchronize LED…
MSI UEFI BIOS is compatible with UEFI (Unified Extensible Firmware Interface) architecture. UEFI has many new functions and advantages that traditional BIOS…
The default settings offer the optimal performance for system stability in normal conditions. You should always keep the default settings to avoid possible…