StarTech.com Desktop Quad Monitor Stand (ARMQUADSS) user manual

Contents

1. Product Diagramp. 11
2. Dimensionsp. 11
3. Front Viewp. 12
4. Rear Viewp. 13

   Shoulder 6 Cable-Management Clip 5 6

5. Side Viewp. 14

   Upper Pole 8 Lower Pole 7 8

6. Technical Specificationsp. 15

   Type of Measurement Measurement VESA Mounting Hole Pattern 75x75 100x100 Weight Capacity Up to 17.6 lb. (8 kg) Per Monitor Tilt +900 to -400 Maximum Screen…

7. Requirementsp. 16

   For the latest requirements, please visit www.startech.com/ARMQUADSS. • Four Monitors Note: All four Monitors must conform to the size, weight, and VESA…

8. Assemblyp. 17

   Warning! Make sure that all of the hardware is assembled properly and checked for stability before you load the Monitors. Warning! Make sure that the weight of…

9. Assemble the Basep. 17

   1. Loosen the Hex Screws that are located on the Base using the 3 mm Hex Key with Screwdriver Tip. 2. Slide the Cable-Management Clip onto the Lower Pole. 3.…

10. Adjust the Collar on the Lower Polep. 18

    1. Loosen the Flat-Head Screws on the Collar, using the 3 mm Hex Key with Screwdriver Tip. 2. Slide the Collar up or down the Lower Pole so that it sits at the…

11. Attach the Shoulder to the Lower Polep. 19

    1. Rotate the Lever on the Shoulder down/counterclockwise to loosen the Shoulder. Freely rotate the Lever by pulling it away from the Shoulder and rotating it…

12. Attach the Swivel Arms to the Lower Polep. 20

    1. Insert the Swivel Arms into the Sockets of the Shoulder until each Swivel Arm clicks into place. (Figure 4) To remove the Swivel Arms: Locate the Clip on…

13. Attach the Upper Polep. 22

    1. Loosen the Hex Screws that are located on the Pole Connector using the 3 mm Hex Key with Screwdriver Tip. 2. Screw the Pole Connector onto the Lower Pole.…

14. Adjust the Collar on the Upper Polep. 23

    1. Loosen the Flat-Head Screws on the Collar located on the Upper Pole, using the 3 mm Hex Key with Screwdriver Tip. 2. Slide the Collar up or down the Upper…

15. Attach the Shoulder to the Upper Polep. 24
16. Attach the Swivel Arms to the Upper Polep. 25

    1. Insert the Swivel Arms into the Sockets of the Shoulder, located on the Upper Pole, until each Swivel Arm clicks into place. (Figure 8) To remove the Swivel…

17. Attach the VESA Mounts to the Monitorsp. 26

    ARMQUADSS is designed to be used with Monitors that are the same size and weight. If you attach Monitors that are different sizes and weights to ARMQUADSS, you…

18. Attach the VESA Mounts to the Swivel Armsp. 28

    Warning! Attaching the Monitors is a two-person job. Do not attempt to complete this task by yourself. Tipping hazard! ARMQUADSS is free-standing and when you…

19. Adjusting the Monitorsp. 30

    Warning! The most stable configuration of ARMQUADSS is the “flat” position, with all four of the Swivel Arms positioned in a straight line. ARMQUADSS can…

20. Tilt Adjustmentp. 30

    Each Monitor can be tilted to accommodate different viewing angles (40 degrees downward or 90 degrees upward). 1. Loosen the Hex Screw on the side of the VESA…

21. Swivel Adjustmentp. 31

    The Monitors can be adjusted on a 360-degree swivel. • Place one hand on the left side of the Monitor and the other hand on the right side of the Monitor.…

22. Rotation Adjustmentp. 31

    The Monitors can be adjusted to be configured in a portrait or landscape view. Note: Ensure that there is ample clearance to fit all four Moni­tors. Some…

23. Micro Height Adjustmentp. 32

    1. Insert the 6 mm Hex Key into the Height-Adjustment Knob that is located on the top of the VESA Mounts. 2. Turn the 6 mm Hex Key, or the Height-Adjustment…

24. Cable Managementp. 33

    The Power and Video Cables from your Monitors can be organized and contained within the Swivel Arms and alongside the Upper and Lower Poles. To manage the…