D-Link 12-port 10GBASE-T (DXS-1210-16TC) user manual

Contents

1. About This Guidep. 7

   This guide provides installation and instructions for the D-Link 10 Gigabit Ethernet L2 Switch (DXS-1210- 12TC/12SC/10TS/16TC), Note: The model you have…

2. Terms/Usagep. 7

   In this guide, the term “Switch” (first letter capitalized) refers to the DSX-1210 Series switch and “switch” (first letter lower case) refers to other…

3. Copyright and Trademarksp. 7

   Information in this document is subjected to change without notice. © 2016 D-Link Corporation. All rights reserved. Reproduction in any manner whatever without…

4. 1 Product Introductionp. 8

   Thank you and congratulations on your purchase of D-Link DXS-1210 Series Switch. D-Link's latest generation L2 10 Gigabit Ethernet switch series blends…

5. 2 Hardware Installationp. 12

   This chapter provides unpacking and installation information for the D-Link DXS-1210 Series Switch

6. Safety Cautionsp. 12

   To reduce the risk of bodily injury, electrical shock, fire and damage to the equipment, observe the following precautions: • Observe and follow service…

7. Step 1: Unpackingp. 13

   Open the shipping carton and carefully unpack its contents. Please consult the packing list located in the User Manual to make sure all items are present and…

8. Step 2: Switch Installationp. 13

   For safe switch installation and operation, it is recommended that you: Visually inspect the power cord to see that it is secured fully to the AC power…

9. Step 3 – Plugging in the AC Power Cordp. 14

   The Switch can now be connected to the AC power. Connect the AC power cord to the rear of the switch and to an electrical outlet (preferably one that is…

10. 3 Getting Startedp. 15

    This chapter introduces the management interface of D-Link DXS-1210 Series Switch

11. Management Optionsp. 15

    The D-Link DXS-1210 Series Switch can be managed through any port by using the Web-based Management, or through any PC using CLI commands. Each switch must be…

12. Using Web-based Managementp. 15

    After a successful physical installation, you can configure the Switch, monitor the network status, and display statistics using a web browser. Supported Web…

13. Smart Wizardp. 16

    After a successful login, the Smart Wizard will guide you through essential settings of the D-Link DXS-1210 Series Switch. Please refer to the Smart Wizard…

14. Web-based Managementp. 16

    By clicking the Exit button in the Smart Wizard, you will enter the Web-based Management interface. Please refer to Chapter 4 Configuration for detailed…

15. D-Link Network Assistant (DNA)p. 16

    is a program that is used to discover switches which are in the same Layer 2 network segment as your PC. You can download the DNA App from the Chrome Web Store…

16. 4 Configurationp. 18

    The features and functions of the D-Link DXS-1210 Series Switch can be configured for optimum use through the Web-based Management Utility

17. Smart Wizard Configurationp. 18
18. Tool Bar > Save Menup. 20

    The Save Menu provides Save Configuration and Save Log functions. Figure 4.5 – Save Menu Save Configuration Select Save configuration to save the configuration…

19. Tool Bar > Tool Menup. 21

    The Tool Menu offers global functions controls such as Reset, Reboot Device, Configuration Backup and Restore, Firmware Backup and Upgrade. Figure 4.7 – Tool…

20. Tool Bar > Smart Wizardp. 24

    By clicking the Smart Wizard button, you can re-run to the Smart Wizard if you wish to make any changes

21. Tool Bar > Online Helpp. 24

    The Online Help provides two ways of online support: D-link Support Site will lead you to the D-Link website where you can find online resources such as…

22. Function Treep. 26

    All configuration options on the switch are accessed through the Setup menu on the left side of the main window. Click on the setup item that you want to…

23. 5 Command Line Interfacep. 121

    The D-Link DXS-1210 Series Switch allows a computer or terminal to perform some basic monitoring and configuration tasks by using the Command Line Interface…

24. To connect a switch via TELNET:p. 121

    1. Make sure the network connection between the switch and PC is active. 2. To connect, launch any terminal software like HyperTerminal in Microsoft Windows…

25. Logging on to the Command Line Interface:p. 121

    Enter your User Name and Password to log on. The default user name and password are ‘admin’. Note that the user name and password are case-sensitive. Press…

26. CLI Commands:p. 121

    The Basic Switch commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Syntax…

27. Appendix A - Technical Specificationsp. 131

    Hardware Specifications Key Components / Performance Switching Capacity: - DXS-1210-10TS: 200Gbps - DXS-1210-12TC: 240Gbps - DXS-1210-12SC: 240Gbps -…

28. Hardware Specificationsp. 131

    Key Components / Performance Switching Capacity: - DXS-1210-10TS: 200Gbps - DXS-1210-12TC: 240Gbps - DXS-1210-12SC: 240Gbps - DXS-1210-16TC: 320Gbps Max.…

29. Featuresp. 132

    L2 Features Supports up to 16K MAC address Jumbo frame: Supports up to 9KB IGMP snooping: Supports 128 multicast group MLD Snooping 802.1D Spanning Tree 802.1s…