D-Link 24-Port Desktop Gigabit Unmanaged PoE Switch (DGS-1026MP) user manual

Contents

1. About This Guidep. 3

   This guide provides instructions to install the D-Link DGS-1026MP 26-Port Unmanaged PoE Gigabit Switch

2. Terms/Usagep. 3

   In this guide, the term “Switch” (first letter capitalized) refers to the DGS-1026MP, and “switch” (first letter lower case) refers to other Ethernet switches.…

3. Copyright and Trademarksp. 3

   Information in this document is subjected to change without notice. © 2016 D-Link Corporation. All rights reserved. Reproduction in any manner whatsoever…

4. Product Introductionp. 4

   The DGS-1026MP is an unmanaged switch with 24 10/100/1000 Mbps ports and 2 Gigabit combo uplink ports. The first 24 10/100/1000 Mbps ports of the DGS-1026MP…

5. Product Overviewp. 4

   Front Panel Figure 1 – DGS-1026MP Front Panel Item Description LED MODE Press to change the port LEDs to display the PoE status or the link status. The color…

6. Hardware Installationp. 6

   This chapter provides more detailed instructions for grounding and installing the DGS-1026MP. CAUTION: Ensure the power cable is disconnected before installing…

7. Installation Precautionsp. 6

   For safe installation and operation of the Switch, it is recommended to: • Visually inspect the DC power jack and make sure that it is fully secured to the…

8. Grounding the Switchp. 6

   This section describes how to connect the Switch to ground. It is necessary to complete this procedure before powering on the Switch. Required Tools and…

9. Attaching the Rubber Feetp. 7

   The DGS-1026MP comes with a strip of four adhesive rubber pads that can be placed on the bottom of the device to prevent the Switch from damaging the surface…

10. Mounting the Switch in a Rackp. 7

    The DGS-1026MP can be easily mounted in a rack using the two provided mounting brackets. Make sure that the front panel is exposed in order to view the LEDs.…

11. Powering on the Switchp. 8

    To power on the Switch, connect the provided power cable to the power socket on the back of the Switch, and connect the adapter side of the cord to a suitable…

12. Connecting the Switchp. 8

    After the DGS-1026MP has been successfully installed, the Switch can be integrated into the network through one of the following three connection methods…

13. Understanding the Switch’s Featuresp. 10

    Power Over Ethernet (PoE) The DGS-1026MP supports many PoE features to guarantee the safety and stability of the Switch and the connected powered devices. PoE…

14. Power Over Ethernet (PoE)p. 10

    The DGS-1026MP supports many PoE features to guarantee the safety and stability of the Switch and the connected powered devices. PoE Power Budget: The total…

15. Power Savingp. 10

    The DGS-1026MP supports IEEE 802.3az Energy Efficient Ethernet (EEE), which will constantly monitor all ports for activity and will put inactive ports into a…

16. Appendix A - Technical Specificationsp. 11

    Hardware Specifications Key Components / Performance Switching Capacity: 52 Gbps Max. Forwarding Rate: 38.69 Mpps Forwarding Mode: Store-and-forward Packet…

17. Hardware Specificationsp. 11

    Key Components / Performance Switching Capacity: 52 Gbps Max. Forwarding Rate: 38.69 Mpps Forwarding Mode: Store-and-forward Packet Buffer memory: 512 Kbytes…

18. Featuresp. 11

    General Features Surge protection Supports up to 8k MAC addresses PoE Features IEEE 802.3af/at compliant Supplies up to 30 watts power per port. Total PoE…

19. Appendix B - Regulatory Statementsp. 12

    FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These…