Loading manual…
Seagate Standard models (ST1000DM003) user manual
- Type
- User manual
- Language
- English
- Pages
- 31
- Category
- Storage & drives
- Models
- ST1000DM003ST500DM002
Open PDFOpens the file on objects.icecat.biz.
Contents
- Desktop HDDp. 1
- Seagate® Technology Support Servicesp. 5
- 1.0 Introductionp. 6
This manual describes the functional, mechanical and interface specifications for the following: Seagate® Desktop HDD model drives: These drives provide the…
- 1.1 About the Serial ATA interfacep. 6
The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: • Easy installation and…
- 2.0 Drive Specificationsp. 7
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this…
- 2.1 Specification summary tablesp. 7
The specifications listed in the following tables are for quick reference. For details on specification measurement or definition, see the appropriate section…
- 2.2 Formatted capacityp. 9
*One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.2.1…
- 2.3 Default logical geometryp. 9
LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors…
- 2.4 Recording and interface technologyp. 9
Model Formatted capacity* Guaranteed sectors Bytes per sector ST1000DM003 1TB 1,953,525,168 4096 physical (emulated at 512-byte sectors) ST500DM002 500GB…
- 2.5 Physical characteristicsp. 10
2.6 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in…
- 2.6 Seek timep. 10
Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table…
- 2.7 Start/stop timesp. 10
Maximum height 1TB models 20.00mm / 0.787 in 500GB models Maximum width 101.85mm / 4.010 in Maximum length 146.99mm / 5.787 in Typical weight 1TB models 415g /…
- 2.8 Power specificationsp. 11
The drive receives DC power (+5V or +12V) through a native SATA power connector. Refer to Figure 1 on page 18. 2.8.1 Power consumption Power requirements for…
- 2.9 Environmental specificationsp. 13
2.9.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature…
- 2.10 Acousticsp. 15
Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound…
- 2.11 Electromagnetic immunityp. 15
When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency…
- 2.12 Reliabilityp. 16
The production disk drive shall achieve an annualized failure-rate of <1.0% over a 5 year service life when used in Desktop Storage field conditions as limited…
- 2.13 Warrantyp. 16
To determine the warranty for a specific drive, use a web browser to access the following web page: http://www.seagate.com/support/warranty-and-replacements/.…
- 2.14 Agency certificationp. 16
2.14.1 Safety certification These products are certified to meet the requirements of UL60950-1, CSA60950-1 and EN60950 and so marked as to the certify agency.…
- 2.15 Environmental protectionp. 18
Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.15.1…
- 2.16 Corrosive environmentp. 18
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous…
- 3.0 Configuring and Mounting the Drivep. 19
This section contains the specifications and instructions for configuring and mounting the drive
- 3.1 Handling and static-discharge precautionsp. 19
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following…
- 3.2 Configuring the drivep. 19
Each drive on the Serial ATA interface connects point-to-point with the Serial ATA host adapter. There is no master/slave relationship because each drive is…
- 3.3 Serial ATA cables and connectorsp. 19
The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connections. The cable size may be 30 to 26 AWG with a…
- 3.4 Drive mountingp. 20
Users can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottommounting holes. See Figure 2 or Figure 3…
- 4.0 Serial ATA (SATA) Interfacep. 22
These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0 to 4…
- 4.1 Hot-Plug compatibilityp. 22
Desktop HDD drives incorporate connectors which enable users to hot plug these drives in accordance with the Serial ATA Revision 2.5 specification. This…
- 4.2 Serial ATA device plug connector pin definitionsp. 22
Table 5 summarizes the signals on the Serial ATA interface and power connectors. Notes 1. All pins are in a single row, with a 1.27 mm (0.050”) pitch. 2. The…
- 4.3 Supported ATA commandsp. 23
The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA…