Philips 27E4U user manual

Contents

1. Safetyp. 3

   National Conventions The following subsections describe national conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks…

2. National Conventionsp. 3

   The following subsections describe national conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be…

3. Powerp. 4

   The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home…

4. Installationp. 5

   Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this…

5. Cleaningp. 6

   Clean the cabinet regularly with a water-dampened, soft cloth. When cleaning use a soft cotton or microfiber cloth. The cloth should be damp and almost dry, do…

6. Otherp. 7

   If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center. Make sure that the ventilating…

7. Setupp. 8

   Contents in Box * * * * * Quick Start Guide HDMI Cable DisplayPort Cable * Monitor Power Cable Stand Base Warranty Card D-SUB Cable USB Cable Audio Cable Not…

8. Set-up Stand & Basep. 9

   Please setup or remove the base following the steps as below. Setup: 1 2 3 5 4 Remove: 5 4 3 1 2

9. Adjusting Viewing Anglep. 11

   To achieve the best viewing experience, it is recommended that the user can make sure they are able to look at their whole face on the screen, then adjust the…

10. Connecting the Monitorp. 12
11. Wall Mountingp. 13

    Preparing to Install An Optional Wall Mounting Arm. 3 1 2 This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before…

12. Adaptive-Sync functionp. 14

    1. Adaptive-Sync function works with DP/HDMI 2. Compatible Graphics Card: Recommended list is as below, also could be checked by visiting www. AMD.com Graphics…

13. Adjustingp. 15

    Hotkeys 1 4 2 3 5 1 Source/Exit 2 Preset Mode/ 3 Brightness/ 4 Menu/Enter 5 Power Menu/Enter Press to display the OSD or confirm the selection. Power Press the…

14. Hotkeysp. 15

    4 2 3 5 1 Source/Exit 2 Preset Mode/ 3 Brightness/ 4 Menu/Enter 5 Power Menu/Enter Press to display the OSD or confirm the selection. Power Press the Power…

15. OSD Settingp. 16
16. LED Indicatorp. 27

    Information Information Input D-SUB Resolution 1920x1080@75Hz Gamma 2.2 SN 000000000 FW Version V1.00 Firmware Date 20250327 Sync NA Brightness 80 OSD Setup…

17. Troubleshootp. 28

    LED Indicator Status LED Color Full Power Mode White Active-off Mode Orange

18. Specificationp. 29

    Troubleshoot Problem & Question Possible Solutions Power LED Is Not ON Make sure the power button is ON and the Power Cord is properly connected to a grounded…

19. General Specificationp. 29
20. AOC Monitors Panel Pixel Defect Policyp. 30

    Specification General Specification Panel Model name 27E4U Driving system TFT Color LCD Viewable Image Size 68.6 cm diagonal Pixel pitch 0.3114mm(H) x…

21. Preset Display Modesp. 32

    - Green + Blue = Cyan (Light Blue) Three adjacent lit sub pixels (one white pixel). Note A red or blue bright dot must be more than 50 percent brighter than…

22. Pin Assignmentsp. 33

    Preset Display Modes STANDARD RESOLUTION(±1Hz) HORIZONTAL FREQUENCY(KHz) VERTICAL FREQUENCY(Hz) VGA 640x480@60Hz 31.469 59.94 640x480@72Hz 37.861 72.809…

23. Plug and Playp. 34

    Pin Assignments 19-Pin Color Display Signal Cable Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name 1. TMDS Data 2+ 9. TMDS Data 0- 17. DDC/CEC…