Loading manual…
Speed Queen SF7 Stacked Washer (SF7008BE) installation instructions
- Type
- Installation instructions
- Language
- English
- Pages
- 29
- Category
- Washing machines
- Models
- SF7008BE
Open PDFOpens the file on content.abt.com.
Contents
- Dimensionsp. 6
- Installationp. 8
Before You Start Tools For most installations, the basic tools you will need are: SWD1021N_SVG 11 10 9 8 4 3 2 1 6 7 5 1. Wrench 2. 1/4 inch Driver 3.…
- Before You Startp. 8
- Position Unit Near Installation Areap. 9
Move unit so that it is within 4 feet [1.2 meters] of the desired area of installation. CAUTION Washer and dryer are not designed to be operated as separated…
- Remove Shipping Materialsp. 9
1. Remove two screws at bottom of front access panel. Rotate bottom of panel out and remove panel. FLW2378N_SVG Figure 2 2. Remove two 9/16 inch bolts and…
- Connect Fill Hosesp. 10
WARNING Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE.…
- Connect Drain Hose to Drain Receptaclep. 12
Remove the drain hose from its shipping position on the rear of the washer by unhooking the hose from the retainer clamp and by removing the shipping tape.…
- Gas Dryers - Connect Gas Supply Pipep. 14
WARNING To reduce the risk of gas leaks, fire or explosion: • The dryer must be connected to the type of gas as shown on nameplate located in the door recess.…
- Electric Dryer Only - Connect Electrical Plugp. 15
Dryer requires 120/240 Volt or 120/208 Volt, 60 Hertz, 3 or 4 wire electrical supply. Refer to serial plate for specific electrical requirements. NOTE…
- Connect Dryer Exhaust Systemp. 19
WARNING To reduce the risk of fire and combustion gas accumulation the dryer MUST be exhausted to the outdoors. W604 WARNING To reduce the risk of fire and the…
- Position and Level the Unitp. 21
WARNING Units elevated above floor level must be anchored to that elevated surface, base or platform. The material used to elevate the unit should also be…
- Reverse Door, if Desiredp. 22
NOTE: Doors with windows cannot be reversed. The door on this dryer is completely reversible. To reverse door proceed as follows: 1. Remove four hinge…
- Wipe Out Inside of Washer and Dryer Drump. 24
IMPORTANT: Prior to first wash, use an all-purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside the drums.…
- Plug In the Washer and Dryerp. 24
Electric Dryer Connect the dryer to an electrical power source. Refer to Connect Electrical Plug section for information on connecting power cord. Connect to…
- Check Installationp. 26
1. Refer to Installer Checklist on the back cover of this manual and make sure that unit is installed correctly. 2. Run washer with a test load to make sure it…
- Check Heat Sourcep. 26
- Installer Checklistp. 28
Fast Track for Installing the Stacked Washer/Dryer 1 Position Unit Near Installation Area. 7 Connect Dryer Exhaust System. SWD997N_SVG1 CHECK CHECK 2 Remove…
- Fast Track for Installing the Stacked Washer/Dryerp. 28
Position Unit Near Installation Area. 7 Connect Dryer Exhaust System. SWD997N_SVG1 CHECK CHECK 2 Remove the Shipping Materials and Install Plugs. 8 Position…
- Refer to the manual for more detailed informationp. 29
Installer Checklist © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 29 Part No. 808186ENR2