Loading manual…
APC InRow™ RC (ACRC301S) installation instructions
Open PDFOpens the file on objects.icecat.biz.
Contents
- Safetyp. 7
Important Safety Information Read the instructions carefully to become familiar with the equipment before trying to install, operate, service, or maintain it.…
- Important Safety Informationp. 7
Read the instructions carefully to become familiar with the equipment before trying to install, operate, service, or maintain it. The following special…
- General Informationp. 8
Inspecting the Cooling Unit Inspect for missing components. All shipped loose components are identified in the “Inventory” on page 10 of this manual. Ensure…
- Inspecting the Cooling Unitp. 8
Inspect for missing components. All shipped loose components are identified in the “Inventory” on page 10 of this manual. Ensure each item is present before…
- Storing the Cooling Unit Before Installationp. 8
If the cooling unit will not be installed immediately, store it in a safe place, protected from the weather
- Moving the Cooling Unitp. 8
The recommended tools for moving the equipment while it is still on the pallet include the following: NOTICE WEATHER DAMAGE Leaving the cooling unit uncovered…
- Model Identificationp. 9
The model number can be found on the outside of the shipping crate and on the name plate located on the rear of the cooling unit as shown. Use the table below…
- Inventoryp. 10
Package contents—ACRC301S Item Description Quantity Item Description Quantity InRow RC—ACRC301S 1 Insulation, bracket 2 Front and rear panel key 2 TORX…
- Component Identificationp. 12
External components—ACRC301S Item Description Upper side panels Fans Display interface Lower side panels Front panel Rear panel Air filters …
- Location, Power, and Water Considerationsp. 19
Room preparation During the design of the data center, consider ease of entry for the equipment, floor loading factors, and accessibility to piping and wiring.…
- Piping Diagramsp. 20
NOTE: Install isolation shutoff valves and particulate strainers in the supply line between the chiller and the CDU. If the system is to be set up as an…
- Installationp. 29
Manual Installation DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Turn off all power supplying this equipment before working on the equipment. All…
- How to Remove Cover Panelsp. 30
The front and rear panels must first be unlocked before they can be removed. Two keys are provided with the unit. CAUTION UNPROTECTED PARTS Be careful when…
- Positioning the Cooling Unitp. 31
Service access An area of 1143 mm (45 in.) of clear floor space in front and 914.4 mm (36 in.) in the rear of the cooling units are required for service.…
- Stabilizing the Cooling Unitp. 32
Bolt-down kit To prevent the cooling unit from moving (if it is not joined with an enclosure), use the included bolt-down kit (AR7701). Follow the installation…
- Mechanical Connectionsp. 34
DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Turn off all power supplying this equipment before working on the equipment. All electrical work must…
- Pipingp. 35
- Waterp. 35
Air Conditioners Installation Manual Piping Ensure that coolant water quality complies with local water quality standards or at least with the guidelines…
- Layout and Piping Considerationsp. 35
Fluid pipes are not allowed directly above electrical cooling units and must be kept separate from any electrical runs or wiring. All fluid piping must be…
- Insulationp. 35
Insulate water lines to protect personnel, protect components from condensate, and to minimize condensation. See “Insulation” on page 40 for insulation…
- Supply and Return Pipingp. 36
NOTE: This section covers a bottom piping configuration only. The ACRC301S model is shown in the illustrations; the process will be the same for ACRC301H…
- Main Water Connectionsp. 39
Top piping system diagram 1. Route all piping to the cooling unit. Be sure to follow all local and national codes. NOTE: Circuit setters are recommended to…
- Additional Equipmentp. 43
Chiller There are three types of chillers to which the cooling unit can be connected: • APC size-matched chiller/thermal storage system • Building…
- Filling and Purgingp. 44
When the installation of the piping is complete, begin the filling process. 1. Open all isolation valves and allow water to flow through the cooling unit. 2.…
- Electrical Connectionsp. 46
The following electrical connections are required in the field: • Primary and secondary feeds • A-Link • Network Management • Rack inlet temperature sensor •…
- Communication Connectionsp. 48
Interface connection Item Description Item Description Universal sensor ports USB host port Network connection Serial port Touchscreen display…
- Power Connectionsp. 58
Power cords may be connected at the top of the cooling unit (standard) or at the bottom (optional). Top configuration—ACRC301S Plug the power cords (supplied)…