APC Smart-UPS On-Line (SRT3000UXI-NCLI) user manual

Contents

1. General Informationp. 3

   Important Safety Messages SAVE THESE INSTRUCTIONS - This manual contains important instructions that should be followed during installation and maintenance of…

2. Important Safety Messagesp. 3

   SAVE THESE INSTRUCTIONS - This manual contains important instructions that should be followed during installation and maintenance of the Smart-UPS and…

3. Product Handling Guidelinesp. 3

   Safety and General Information • Adhere to all national and local electrical codes. • All wiring must be performed by a qualified electrician. • Changes and…

4. Safety and General Informationp. 3

   Adhere to all national and local electrical codes. • All wiring must be performed by a qualified electrician. • Changes and modifications to this unit not…

5. Product Descriptionp. 5

   The APC by Schneider Electric Smart-UPS™ On-Line SRT is a high performance uninterruptible power supply (UPS). The UPS helps to provide protection for…

6. Product Overviewp. 6

   Specifications For additional specifications refer to the APC by Schneider Electric web site, www.apc.com. Environmental Physical Battery NOTES: • The UPS does…

7. Specificationsp. 6

   For additional specifications refer to the APC by Schneider Electric web site, www.apc.com. Environmental Physical Battery NOTES: • The UPS does not support…

8. Front Panel Featuresp. 7

   Overvoltage Category II Applicable power grid power distribution system TN Power System Applicable standard IEC 62040-1 Models Rating Building Circuit Breaker…

9. Rear Panel Featuresp. 8

   Note: Refer to the table “Key to identify rear panel features” on this page, that provides a key to the callout numbers for the rear panel graphics depicted in…

10. Operationp. 9

    Connect Equipment Note: The XLBP batteries will charge to 90% capacity in the first three hours of normal operation. Do not expect full battery runtime…

11. Connect Equipmentp. 9

    Note: The XLBP batteries will charge to 90% capacity in the first three hours of normal operation. Do not expect full battery runtime capability during this…

12. Turn the UPS On/Offp. 9

    The first time the UPS is turned on the Setup Wizard screen will run. Follow the prompts to configure UPS settings. Refer to “Configuration” on page 11. To…

13. UPS Display Interfacep. 10

    operation Use the UP/DOWN buttons to scroll through the options. Press the OK button to accept the selected option. Press the ESC button to return to the…

14. Configurationp. 14

    UPS Settings There are three ways to select UPS configuration options. 1. The first time the UPS is turned on the Setup Wizard screen will open. On each menu…

15. UPS Settingsp. 14

    There are three ways to select UPS configuration options. 1. The first time the UPS is turned on the Setup Wizard screen will open. On each menu screen select…

16. Controllable Outlet Groupsp. 19

    provide battery backup power to connected equipment. Overview The controllable outlet groups can be configured using the Advanced menu options. Refer to…

17. Emergency Power Offp. 20

    Overview The Emergency Power Off (EPO) option is a feature that will immediately disconnect all connected equipment from mains power. The UPS will immediately…

18. Network Management Interface (For NC models only)p. 21

    Introduction The UPS has a network port and console port that can be used to access the Network Management Interface. Refer to the Network Management Card…

19. Introductionp. 21

    The UPS has a network port and console port that can be used to access the Network Management Interface. Refer to the Network Management Card installation…

20. IP Address Configurationp. 21

    The default TCP/IP configuration setting DHCP, assumes that a properly configured DHCP server is available to provide TCP/IP settings to the Network Management…

21. Related Documentsp. 21

    For related documents refer APC by Schneider Electric Web site, www.apc.com

22. Smart Battery Managementp. 22

    Definitions • Smart External Battery Pack (XLBP): An enclosure that contains RBC(s) and battery management electronics. • User Interface (UI): Any interface by…

23. Troubleshootingp. 23

    Use the table below to solve minor installation and operation problems. Refer to the APC by Schneider Electric web site, www.apc.com for assistance with…

24. Transportp. 25

    1. Shut down and disconnect all connected equipment. 2. Disconnect the unit from mains power. 3. Disconnect all internal and external batteries (if…

25. Servicep. 25

    section of this manual. Service If the unit requires service, do not return it to the dealer. Follow these steps: 1. Review the Troubleshooting section of the…

26. Limited Factory Warrantyp. 26

    Schneider Electric IT Corporation (SEIT), warrants its products to be free from defects in materials and workmanship for a period of five (5) years from the…