APC Smart-UPS On-Line (SRTL1500RM4UXLI) user manual

Contents

1. General Informationp. 3

   Important Safety Messages Read the instructions carefully to become familiar with the equipment before attempting to install, operate, service or maintain the…

2. Important Safety Messagesp. 3

   Read the instructions carefully to become familiar with the equipment before attempting to install, operate, service or maintain the UPS. The following special…

3. Product Handling Guidelinesp. 3

   Safety and General Information • Adhere to all national and local electrical codes. • All wiring must be performed by a qualified electrician. • Changes and…

4. Safety and General Informationp. 3

   Adhere to all national and local electrical codes. • All wiring must be performed by a qualified electrician. • Changes and modifications to this unit not…

5. Deenergizing safetyp. 4

   Battery packs connected to the UPS may present a shock hazard even when disconnected from the branch circuit (mains). Before installing or servicing the…

6. Electrical safetyp. 4

   In order to maintain compliance with the EMC directive for products sold in Europe, output cords and network cables attached to the UPS must not exceed 10…

7. Battery safetyp. 4

   Servicing of batteries should be performed or supervised by personnel knowledgeable about batteries and the required precautions. Keep unauthorized personnel…

8. General informationp. 5

   Refer to “Specifications” on page 5 for information on the maximum number of battery packs supported by your UPS model. Note: For each battery pack added…

9. Product Descriptionp. 5

   The APC by Schneider Electric Smart-UPS™ On-Line SRT is a high performance uninterruptible power supply (UPS). The UPS helps to provide protection for…

10. Product Overviewp. 6

    Specifications For additional specifications refer to the APC by Schneider Electric web site, www.apc.com

11. Specificationsp. 6

    For additional specifications refer to the APC by Schneider Electric web site, www.apc.com

12. Environmentalp. 6
13. Physicalp. 6

    Battery NOTES: • The UPS does not support any other type/make of battery packs. • Refer to the appropriate replacement battery user manual for installation…

14. Batteryp. 6

    NOTES: • The UPS does not support any other type/make of battery packs. • Refer to the appropriate replacement battery user manual for installation…

15. Electricalp. 7

    CAUTION: To reduce the risk of fire, connect the UPS only to a circuit provided with recommended maximum branch circuit overcurrent protection

16. Front Panel Featuresp. 7

    Overvoltage Category II Applicable power grid power distribution system TN Power System Applicable standard IEC 62040-1 Models Rating Building Circuit Breaker…

17. Rear Panel Featuresp. 8

    Note: Refer to the table “

18. SRT1000/1500 UXI-LIp. 8

    Tower/Rack-Mount 6 Rear Panel Features Note: Refer to the table “

19. SRT1000/SRT1500 UXI-NCLIp. 8

    Key to identify rear panel features SmartSlot The SmartSlot can be used to connect optional management accessories. AC inlet Connect the UPS to utility power…

20. Key to identify rear panel featuresp. 8

    ” on this page, that provides a key to the callout numbers for the rear panel graphics depicted in this manual. SRT1000/1500 UXI-LI SRT1000/SRT1500 UXI-NCLI…

21. Operationp. 9

    Connect Equipment Note: The XLBP will charge to 90% capacity in the first ten hours of normal operation. Do not expect full battery runtime capability during…

22. Connect Equipmentp. 9

    Note: The XLBP will charge to 90% capacity in the first ten hours of normal operation. Do not expect full battery runtime capability during this initial charge…

23. Turn the UPS On/Offp. 9

    The first time the UPS is turned on the Setup Wizard screen will run. Follow the prompts to configure UPS settings. Refer to “Configuration” on page 11. To…

24. UPS Display Interfacep. 10

    operation Use the UP/DOWN buttons to scroll through the options. Press the OK button to accept the selected option. Press the ESC button to return to the…

25. UPS Display Interface operationp. 10

    Use the UP/DOWN buttons to scroll through the options. Press the OK button to accept the selected option. Press the ESC button to return to the previous menu.…

26. LCD display interface angle adjustmentp. 12

    The angle of the LCD display interface can be adjusted for ease in viewing the displayed messages. 1. Remove the front bezel. 2. Locate the button on the…

27. Menu overviewp. 12

    The UPS Display Interface has Standard and Advanced menu screens. The preference for Standard or Advanced menu selections is made during initial installation…

28. Configurationp. 14

    UPS Settings There are three ways to select UPS configuration options. 1. The first time the UPS is turned on the Setup Wizard screen will open. On each menu…

29. UPS Settingsp. 14

    There are three ways to select UPS configuration options. 1. The first time the UPS is turned on the Setup Wizard screen will open. On each menu screen select…

30. Startup configurationp. 14

    Function Description Select the language required for the display interface. Language options will vary by model and firmware version. Options: • English •…