APC Uninterruptible Power Supply (SRT8KXLI) user manual

Contents

1. Safety Messagesp. 3

   Read the instructions carefully to become familiar with the equipment before attempting to install, operate, service or maintain the UPS. The following special…

2. Safety and General Informationp. 4

   Adhere to all national and local electrical codes. • All wiring must be performed by a qualified electrician. • Changes and modifications to this unit not…

3. Deenergizing safetyp. 4

   The UPS contains internal batteries and may present a shock hazard even when disconnected from the branch circuit (mains). Before installing or servicing the…

4. Electrical safetyp. 4

   For models with a hardwired input, the connection to the branch circuit (mains) must be performed by a qualified electrician. • 230 V models only: In order to…

5. Battery safetyp. 5

   Before installing or replacing the batteries, remove jewelry such as wristwatches and rings. High short circuit current through conductive materials could…

6. Hardwire safetyp. 5

   Verify that all branch circuit (mains) and low voltage (control) circuits are deenergized, and locked out before installing cables or making connections…

7. General informationp. 5

   The UPS will recognize as many as 10 external battery packs connected to the UPS. However there is no limit to the number of XLBPs that can be used with the…

8. Specificationsp. 6

   For additional specifications refer to the APC web site, www.apc.com

9. Environmentalp. 6
10. Physicalp. 6
11. Batteryp. 6
12. Electricalp. 7
13. Front panel featuresp. 7
14. Rear panel featuresp. 8

    Note: Refer to the table “Key to identify rear panel features” on page 8, that provides a key to the callout numbers for the rear panel graphics depicted in…

15. Key to identify rear panel featuresp. 10

     Network port Use the Network port to connect the UPS to the network.  Console port Use the Console port to configure the network management features. …

16. Wiring Specificationsp. 11

    * Phase 1 (L1) current while in bypass mode CAUTION DAMAGE TO EQUIPMENT OR PERSONNEL • Adhere to all national and local electrical codes. • Wiring should be…

17. Connect Equipmentp. 13

    Note: The UPS batteries will charge to 90% capacity in the first three hours of normal operation. Do not expect full battery runtime capability during this…

18. Turn the UPS On/Offp. 13

    The first time the UPS is turned on the Setup Wizard screen will run. Follow the prompts to configure UPS settings. Refer to “Configuration” on page 15. To…

19. UPS Display Interfacep. 14

     POWER ON/OFF button Button illumination indications: -No illumination, the UPS and the output power are off -White illumination, the UPS and the output power…

20. UPS Display Interface operationp. 15

    Use the UP/DOWN buttons to scroll through the options. Press the OK button to accept the selected option. Press the ESC button to return to the previous menu

21. Menu overviewp. 15

    The UPS Display Interface has Standard and Advanced menu screens. The preference for Standard or Advanced menu selections is made during initial installation…

22. LCD display interface angle adjustmentp. 16

    The angle of the LCD display interface can be adjusted for ease in viewing the displayed messages. 1. Remove the front bezel. 2. Locate the button on the…

23. UPS Settingsp. 18

    There are four ways to select UPS configuration options. 1. The first time the UPS is turned on the Setup Wizard screen will open. On each menu screen select…

24. Startup configurationp. 18

    Function Description Select the language required for the UPS Display Interface. Language options will vary by model and firmware version. Options: • English •…

25. General settingsp. 19

    Configure these settings at any time, using the UPS Display Interface, or the Network Management web Interface. Parameters Default Value Options Description…

26. Controllable Outlet Groups provide battery backup power to connected equipmentp. 22

    Overview The controllable outlet groups can be configured using the Advanced menu options. Refer to “General settings” on page 16. The controllable outlet…

27. Overviewp. 22

    The controllable outlet groups can be configured using the Advanced menu options. Refer to “General settings” on page 16. The controllable outlet groups can be…

28. Connect controllable outlet groupsp. 22

    Connect critical equipment to one controllable outlet group. • Connect peripheral equipment to the other controllable outlet groups. – To conserve battery…

29. Overviewp. 23

    The Emergency Power Off (EPO) option is a feature that will immediately disconnect all connected equipment from mains power. The UPS will immediately shut down…

30. Normally open contactsp. 23

    1. If the EPO switch or relay contacts are normally open, insert the wires from the switch or contacts at pins 1 and 2 of the EPO terminal block. Use 16-28 AWG…

Other documents for this model

• APC Smart-UPS (SRT8KRMXLT-5KTF) installation instructions