APC SRT (SRT5KXLI) user manual

Contents

1. Product Descriptionp. 3

   The APC™ by Schneider Electric Smart-UPS™ On-Line SRT is a high performance uninterruptible power supply (UPS). The UPS helps to provide protection for…

2. General Informationp. 3

   Safety Messages Read the instructions carefully to become familiar with the equipment before attempting to install, operate, service or maintain the UPS. The…

3. Safety Messagesp. 3

   Read the instructions carefully to become familiar with the equipment before attempting to install, operate, service or maintain the UPS. The following special…

4. Safety Informationp. 4

   Adhere to all national and local electrical codes. • All wiring must be performed by a qualified electrician. • Changes and modifications to this unit not…

5. Product Overviewp. 6

   Specifications For additional specifications refer to the APC web site, www.apc.com. Environmental Physical Temperature Operating 0º to 40º C (32º to 104º F)…

6. Specificationsp. 6

   For additional specifications refer to the APC web site, www.apc.com. Environmental Physical Temperature Operating 0º to 40º C (32º to 104º F) Storage -15º to…

7. Front panel featuresp. 8

   Display interface panel UPS battery connectors Battery compartment Bezel su0877a

8. Rear panel featuresp. 9

   Note: Refer to the table “Key to identify rear panel features” on page 10, that provides a key to the callout numbers for the rear panel graphics depicted in…

9. Wiring Specificationsp. 13

   CAUTION DAMAGE TO EQUIPMENT OR PERSONNEL • Adhere to all national and local electrical codes. • Wiring should be performed by a qualified electrician. • Strain…

10. Connect Equipmentp. 15

    Note: The UPS batteries will charge to 90% capacity in the first three hours of normal operation. Do not expect full battery runtime capability during this…

11. Turn the UPS On/Offp. 15

    The first time the UPS is turned on the Setup Wizard screen will run. Follow the prompts to configure UPS settings. Refer to “Configuration” on page 17. To…

12. UPS Display Interfacep. 16

     POWER ON/OFF button Button illumination indications: -No illumination, the UPS and the output power are off -White illumination, the UPS and the output power…

13. Configurationp. 20

    UPS Settings There are four ways to select UPS configuration options. 1. The first time the UPS is turned on the Setup Wizard screen will open. On each menu…

14. UPS Settingsp. 20

    There are four ways to select UPS configuration options. 1. The first time the UPS is turned on the Setup Wizard screen will open. On each menu screen select…

15. Controllable Outlet Groupsp. 24

    provide battery backup power to connected equipment. Overview The controllable outlet groups can be configured using the Advanced menu options. Refer to…

16. Emergency Power Offp. 25

    Overview The Emergency Power Off (EPO) option is a feature that will immediately disconnect all connected equipment from mains power. The UPS will immediately…

17. Network Management Interfacep. 26

    Introduction The UPS has a network port and console port that can be used to access the Network Management Interface. The Network Management Interface is very…

18. Introductionp. 26

    The UPS has a network port and console port that can be used to access the Network Management Interface. The Network Management Interface is very similar to an…

19. Featuresp. 26

    The Network Management Interface allows the UPS to function as a Web based, IPv6 ready product. The Network Management Interface can manage the UPS using…

20. Related Documentsp. 27

    The Network Management Card Utility CD contains the following documentation: • UPS Network Management Card 2 User’s Guide • Network Management Card Upgrade…

21. IP Address Configurationp. 27

    The default TCP/IP configuration setting DHCP, assumes that a properly configured DHCP server is available to provide TCP/IP settings to the Network Management…

22. Smart Battery Managementp. 28

    Definitions • Battery Module: A string of battery cells arranged to produce a battery assembly with a connector. • Replaceable Battery Cartridge (RBC): An APC…

23. Troubleshootingp. 30

    Use the table below to solve minor installation and operation problems. Refer to the APC web site, www.apc.com for assistance with complex UPS problems. The…

24. Transportp. 33

    1. Shut down and disconnect all connected equipment. 2. Disconnect the unit from mains power. 3. Disconnect all internal and external batteries (if…

25. Servicep. 33

    section of this manual. Service If the unit requires service, do not return it to the dealer. Follow these steps: 1. Review the Troubleshooting section of the…

26. Limited Factory Warrantyp. 34

    Schneider Electric IT Corporation (SEIT), warrants its products to be free from defects in materials and workmanship for a period of three (3) years excluding…