MSI MPG27CQ2 (OPTIX MPG27CQ2) user manual

Contents

1. Copyright and Trademarks Noticep. 3

   Copyright © Micro-Star Int’l Co., Ltd. All rights reserved. The MSI logo used is a registered trademark of Micro-Star Int’l Co., Ltd. All other marks and names…

2. Revisionp. 3
3. Technical Supportp. 3

   If a problem arises with your product and no solution can be obtained from the user’s manual, please contact your place of purchase or local distributor.…

4. Safety Instructionsp. 4

   ◙ ◙ Read the safety instructions carefully and thoroughly. ◙ ◙ All cautions and warnings on the device or user’s manual should be noted. ◙ ◙ Refer servicing to…

5. CE Conformityp. 6

   This device complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic…

6. FCC-B Radio Frequency Interference Statementp. 6

   This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are…

7. WEEE Statementp. 7

   Under the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment, Directive 2002/96/EC, which takes effect on August 13, 2005, products…

8. Chemical Substances Informationp. 7

   In compliance with chemical substances regulations, such as the EU REACH Regulation (Regulation EC No. 1907/2006 of the European Parliament and the Council)…

9. RoHS Statementp. 7

   Japan JIS C 0950 Material Declaration A Japanese regulatory requirement, defined by specification JIS C 0950, mandates that manufacturers provide material…

10. Getting Startedp. 9

    This chapter provides you with the information on hardware setup procedures. While connecting devices, be careful in holding the devices and use a grounded…

11. Installing the Monitor Standp. 11

    1. Fit the stand to the monitor. 2. Push down the latch to lock the stand in place. 3. Connect the base to the stand and tighten the base screw to secure the…

12. Adjusting the Monitorp. 12

    This monitor is designed to maximize your viewing comfort with its adjustment capabilities such as tilt, lift and swivel. IMPORTANT Avoid touching the display…

13. Monitor Overviewp. 13
14. Connecting the Monitor to PCp. 15

    1. Turn off your computer. 2. Connect the HDMI/DisplayPort cable from the monitor to your computer. 3. Assemble the monitor power adapter & power cord. (Figure…

15. Wall Mounting (Optional)p. 16

    1. Release the base screw and detach the base. 2. Pull up the latch to unlock the stand. 3. Disassemble the stand. 4. Remove the pre-installed screws for VESA…

16. OSD Setupp. 17

    This chapter provides you with essential information on OSD Setup. IMPORTANT All information is subject to change without prior notice.

17. Navi Keyp. 18

    The monitor comes with a Navi Key, a multi-directional control that helps navigate the On-Screen Display (OSD) menu. Navi Key

18. OSD Setup via Navi Keyp. 21

    Press the Middle button of Navi Key to launch the On-Screen Display (OSD) main menu. Use the Up, Down, Left, Right buttons to tune the desired function menus…

19. Appendixp. 29

    IMPORTANT All information is subject to change without prior notice.

20. Specificationsp. 30

    Model Optix MPG27C Optix MPG27CQ Optix MPG27CQ2 Size 27 inch Curvature 1800R Panel Type VA Resolution 1920 x 1080@144Hz 2560 x 1440@144Hz Aspect Ratio 16:9…

21. Preset Display Modesp. 32
22. Troubleshootingp. 33

    The power LED is off. • • Press the monitor power button again. • • Check if the monitor power cable is properly connected. No image. • • Check if the computer…