Loading manual…
Fisher & Paykel RS6009V2RT1 installation instructions
- Type
- Installation instructions
- Language
- English
- Pages
- 48
- Category
- Refrigerators & freezers
- Models
- RS6009SBL1RS6009SBLT1RS6009V2R1RS6009V2RT1
Open PDFOpens the file on fisherpaykel.com.
Contents
- Tools requiredp. 2
Supplied Not supplied F Spanner F L key combi PH T25 F M4 ball allen key F Powered driver F Flathead screwdriver F Measuring tape F Phillips screwdriver F…
- Parts requiredp. 3
INSTALL KIT Install Kit A (bracket anti-tip assembly) Install kit E (kit screw alcove attachment) Install kit F (kit panel attach) Install kit G (kit screw…
- Accessing your product specificationsp. 5
For full product, cabinetry and service specifications, refer to the Planning Guide. To access the Planning Guide, scan the QR code or visit…
- Prior to installationp. 6
1. Measure alcove. Ensure all minimum specifications have been met. Refer to the planning guide for details. fisherpaykel.com/specify 3. Ensure alcove is…
- Unpackingp. 8
1. Cut the straps, open the top and cut down the side of the carton to remove. Remove all pre-packaged parts. 2. Dispose of packaging responsibly. 3. Using a…
- Install anti-tip bracketp. 10
1. Ensure wall stud or solid surface is present. 2. If alcove depth is greater than 600mm A spacer will be required to be installed alongside the anti-tip…
- Remove grillep. 12
1. Push the grille flap to open. 2. Unscrew the two Phillips screws from behind the flap and the five screws from the grille front. Set aside. 3. Pull the…
- Hinge swap (optional)p. 13
1. Open the door. 2. Loosen the hinge screws using the supplied Torx T25 driver. Slide door off and place on a protected surface. 3. Carefully remove hinges…
- Join products (multiple installs only)p. 17
1. Ensure doors are closed before rolling products into position. 2. Secure the lower front bracket using four screws. 3. Secure the upper front bracket using…
- Install depth gauges and spacersp. 19
1. Clip both hinge spacers onto the product. For right-hand hinge installations, ensure spacer A is fitted to the top hinge and spacer B is fitted to the…
- Connect powerp. 21
1. If required, wrap a thread around the power cord to bring any slack inside the plinth to reduce the risk of it tangling behind the product. 2. Connect to…
- Push into cavityp. 22
1. Push product in until the depth gauges touch the front of the alcove. Ensure power cord is not trapped.
- Adjust heightp. 23
1. Adjust the front of the product by turning the lefthand screw anti-clockwise to lower the feet. We recommend marking a drill and counting the number of…
- Securep. 25
1. Using two supplied long Phillips screws, secure the lower hinge to the cavity 2. Using one supplied short Phillips screw, secure the lower right side of the…
- Door panel prep (custom panel)p. 28
1. Recheck the door panel specifications. Ensure all bracket locations have been marked. Refer to the Planning Guide for details. 2. Unscrew the two Phillips…
- Door panel prep (pre-finished panel)p. 31
1. Unscrew the two Phillips screws to remove the top cover. 2. Remove both washers and nuts and set aside. Lift the panel bracket outwards to remove. 3. Remove…
- Align door panelp. 33
1. Ensure top mounting screws have been loosened and sit at their lowest position 2. Lower the door panel onto the mounting screws 3. Fit a tab to the door to…
- Secure door panelp. 36
1. With the door open, loosen the lower bracket screw. Adjust bracket to rest against the door panel. Re-tighten the bracket screw. 2. Fit an additional screw…
- Fit trimsp. 37
1. Fit the top cover using two supplied Phillips screws. Ensure the flat side faces away from the panel. 2. Locate the shorter door trim to the hinge-side of…
- Install centre trim (multiple product installations)p. 40
1. Locate the centre trim between products and push into position. Ensure the lower part of the trim clears the grille. 2. Slide trim up to slot into the upper…
- Refit grillep. 41
1. Open the cover and align the grille to the product. Slot into place starting with the base of the grille. 2. Hand tighten the top left screw, followed by…
- Prepare toe kickp. 42
1. Recheck toe kick panel specifications. Refer to the Planning Guide for details. 2. Measure the distance from the floor to the bottom of the grille to…
- Secure toe kickp. 43
1. Loosen the screws on both toe kick brackets and slide brackets forward. Re-tighten screws slightly. 2. Locate the toe kick to the magnetic brackets to…
- Secure flow dividerp. 45
1. With the door open, align flow divider to base of door. Using either a hacksaw or side cutters, cut divider to ensure it doesn't extend below the door…
- Exit install modep. 46
1. Press and hold to exit install mode
- Installer checklistp. 47
F Ensure Installer Mode has been exited. F All levelling feet have been adjusted and engaged. F Panel gaps and any potential clashing points have been checked.…