Loading manual…
Fisher & Paykel DD24DDFTX9 installation instructions
- Type
- Installation instructions
- Language
- English
- Pages
- 42
- Models
- DD24DAX9DD24DCHTX9DD24DCTX9DD24DDFTX9DD24DT2NX9DD24DT4NX9DD24DVT9
Open PDFOpens the file on fisherpaykel.com.
Contents
- Components requiredp. 4
TOOLS Supplied F 1x Foot adjusting tool Not supplied F Box cutter F Cross head screwdriver F Flat blade screw driver F Drill F 1x 13mm Drill bit F 1x 2.5mm…
- Accessing your product specificationsp. 5
For full product, cabinetry and service specifications, refer to the Planning Guide. To access the Planning Guide, scan the QR code or visit…
- Panel specificationsp. 7
- Prior to installationp. 8
1. Refer to the Planning Guide for cabinetry, cavity and service specifications. fisherpaykel.com/specify 2. Ensure the cabinet meets the minimum cavity…
- Unpack all productsp. 11
1. Carefully remove the plastic wrap. 2. Protect flooring before removing the base. 3. To detach the base, use a trolley to lift the dishwasher from the rear…
- Hard wiring (optional)p. 13
A qualified electrician is required to hard wire the dishwasher. Remove the supplied power cord and complete the hard-wiring close to the cavity. 1. Pull the…
- Apply sealing tapep. 17
1. Ensure underside of countertop is clean and dust free. 2. Remove backing from tape 3. Apply tape to countertop ensuring it is centred and set back 3/8" from…
- Dishwasher Securing optionsp. 18
1. Securing through chassis: Screws must be fixed through the chassis sides and into the cabinet sides or packers. 2. Securing through side brackets: Middle or…
- To attach side bracketsp. 19
1. Locate the upper and lower bracket sets. 2. If using the upper bracket set, insert into the slots and tap gently with a soft mallet to secure. Push the…
- To attach top bracketsp. 20
2. If necessary, tap gently with a soft mallet to secure. Use top brackets if the cabinetry is suitable and the screws heads will be flush to prevent drawer…
- Attach Spacersp. 21
1. Snap off the four spacers with an adhesive strip. 2. Place spacers on each side of the dishwasher between the brackets. 3. If required a larger spacer…
- Adjust dishwasher heightp. 22
1. Measure the height of the dishwasher from the feet to the top of the chassis. 2. Measure the distance from the floor to the underside of the countertop or…
- Push inside cavityp. 24
1. Place hoses and cords through the service holes and into the adjacent cavity. 2. Carefully push the product into the cavity, feeding the hoses through the…
- Level the dishwasherp. 25
1. Measure the gap between the top of the drawer panel and the countertop or frame for height adjustment. 2. Pull the lower drawer halfway out to remove the…
- Secure through chassis slotp. 27
3. On the chassis sides, lift the insulation. Slots in the chassis sides allow screws to be temporarily fixed and the dishwasher to be adjusted within the…
- Secure using bracketsp. 30
1. If using side brackets, partially open the top drawer. Lift the rubber seal and remove the left and right screw covers from the trim. 2. Fix side brackets…
- Install pre-finished toe kickp. 31
1. Open the bottom drawer. Rotate the toe kick so the tabs are resting on the floor. 2. Mark the point where the toe kick meets the edge of the tub. Select the…
- Drain connection optionsp. 33
Water softener models: Water pressure: maximum 1 MPa (145 psi), min. 0.1 MPa (14.5 psi). Non-water softener models: Water pressure: maximum 1 MPa (145 psi)…
- Install drainp. 36
3. Thread wire clips on to the hoses. Fit the hoses to the supplied hose joiner and secure using the wire clips provided. Ensure hose is routed straight to the…
- Connect water inletp. 38
Do not turn water supply on before power has been connected. The dishwasher must be powered on for flood protection to be enabled. Isolation taps are required…
- Connect powerp. 39
1. Connect power. 2. Check the water connections. Turn on the water supply and check for leaks. The dishwasher must be powered on for flood protection to be…
- Installer checklistp. 40
Installation F If power is disconnected, ensure water supply is turned off to prevent flooding. F Check all parts are installed correctly and are secure. F…