Loading manual…
Fisher & Paykel DD60DI9 installation instructions
Open PDFOpens the file on fisherpaykel.com.
Contents
- Components requiredp. 3
TOOLS Supplied F 1x Foot adjusting tool Not supplied F Box cutter F Cross head screwdriver F Flat blade screw driver F Drill F 1x 13mm Drill bit F 1x 2.5mm…
- Accessing your product specificationsp. 4
For full product, cabinetry and service specifications, refer to the Planning Guide. To access the Planning Guide, scan the QR code or visit…
- Prior to installationp. 6
1. Refer to the Planning Guide for cabinetry, cavity, panel and service specifications. fisherpaykel.com/specify 2. Ensure the cabinet meets the minimum cavity…
- Prior to installation - servicesp. 8
Refer to the Planning Guide at fisherpaykel.com for service options. 1. A minimum 57mm diameter service hole is required in the cabinet side. The center of the…
- Unpack all productsp. 9
1. Remove the plastic wrap. 2. Protect flooring before removing the packing base. 3. To detach the base, use a trolley to lift the dishwasher from the rear…
- Apply sealing tapep. 11
1. Ensure underside of countertop is clean and free of dust. 2. Remove backing from tape 3. Apply tape to top edge of cabinet ensuring it is centred and set…
- Dishwasher Securing optionsp. 12
1. Securing through chassis: Screws must be fixed through the chassis sides and into the cabinet sides or packers. 2. Securing through side brackets: Middle or…
- To Attach side bracketsp. 13
1. Locate the upper and lower bracket sets. 2. If using the upper bracket set, insert into the slots and tap gently with a soft mallet to secure. Push the…
- To Attach top bracketsp. 14
2. If necessary, tap gently with a soft mallet to secure. Use top brackets if the cabinetry is suitable and the screws heads will be flush to prevent drawer…
- Attach Spacersp. 15
1. Snap off the four spacers with an adhesive strip. 2. Place spacers on each side of the dishwasher between the brackets. 3. If required a larger spacer…
- Adjust dishwasher heightp. 16
1. Measure the height of the dishwasher from the feet to the top of the chassis. 2. Measure the distance from the floor to the underside of the countertop or…
- Push inside cavityp. 18
1. Place hoses and cords through the service holes and into the adjacent cavity. 2. Carefully push the product into the cavity, feeding the hoses through the…
- Level the dishwasherp. 19
2. Remove the panel and pull the drawer halfway out to remove the tub. On each side of the lower drawer, push locking tabs back. 3. Place the drawer on a…
- Custom top panel: measurep. 21
If panels widths or heights are extended over the minimum dimensions, ensure there is a small gap between the custom panel and any cabinetry behind it. The…
- Custom top panel: attach to door bracketp. 22
2. Detach the door bracket by pulling down firmly and then angling out. Disconnect the earth wire from the bracket before removing. 3. Position the door…
- Custom top panel: install knock-to-pause modulep. 24
1. Secure knock-to-pause module to the panel using the supplied screws. 2. Check that the module is oriented correctly and fixed securely to ensure proper…
- Secure TOP panelp. 25
- Custom bottom panel: measure panelp. 26
2. Subtract the required gap between the cabinet panels from each measurement. B 3. Use the final measurements to mark vertical lines on the back of the custom…
- Custom Bottom panel: Attach to door bracketp. 27
3. Position the door bracket on the custom panel between the marked lines. Ensure that the top of the drawer bracket rests on the panel. 2. Detach the door…
- Bottom panel: Attach to door bracketp. 28
5. Slot panel onto dishwasher. Check that the gaps between the panel and adjacent cabinet doors are a minimum of 2mm. Check that the gap between the top and…
- Custom bottom panel: install knock-to-pause modulep. 29
- Secure BOTTOM panelp. 30
- SECURE through chassis slotp. 31
3. On the chassis sides, lift the insulation. Slots in the chassis sides allow screws to be temporarily fixed and the dishwasher to be adjusted within the…
- Secure through chassis slotp. 32
4. Fit a screw in each chassis slot to secure to the cabinet. Partially tighten screws ensuring adjustments can be made. 6. To replace the bottom tub, pull the…