TP-Link Omada 32-Port 10GE SFP+ L2+ Managed Switch (SX3032F) installation instructions

Contents

1. Chapter 1 Introductionp. 5

   1.1 Product Overview Designed for workgroups and departments, TP-Link Omada's L2+ Managed Switch provides wire-speed performance and abundant L2 management…

2. 1.1 Product Overviewp. 5

   Designed for workgroups and departments, TP-Link Omada's L2+ Managed Switch provides wire-speed performance and abundant L2 management features. It provides a…

3. 1.2 Appearancep. 5

   Front Panel (The figures are for demonstration only. They may differ from your actual products.) The front panel of SX3206HPP is shown as the following figure.…

4. Chapter 2 Installationp. 22

   2.1 Package Contents Make sure that the package contains the following items. Please contact your distributor, if any of the listed items is damaged or…

5. 2.1 Package Contentsp. 22

   Make sure that the package contains the following items. Please contact your distributor, if any of the listed items is damaged or missing. The figures are for…

6. 2.2 Safety Precautionsp. 22

   To avoid any device damage and bodily injury caused by improper use, you should observe the following rules. • Safety Precautions • Keep the power off during…

7. 2.3 Installation Toolsp. 24

   Phillips screwdriver • ESD-preventive wrist wrap • Cables Note: These tools are not included with our product. If needed, you can purchase them separately

8. 2.4 Product Installationp. 24

   Desktop Installation To install the device on the desktop, follow the steps: 1. Set the device on a flat surface which is strong enough to support the entire…

9. Chapter 3 Connectionp. 26

   3.1 Ethernet Port Connect an Ethernet port of the switch to the computer by RJ45 cable as the following figure shows. Figure 3-1 Connecting the RJ45 Port RJ45…

10. 3.1 Ethernet Portp. 26

    Connect an Ethernet port of the switch to the computer by RJ45 cable as the following figure shows. Figure 3-1 Connecting the RJ45 Port RJ45 Port RJ45 Cable

11. 3.2 SFP/SFP+ Slotp. 26

    The following figure demonstrates the connection of SFP/SFP+ slot to an SFP/SFP+ module. Figure 3-2 Inserting the SFP/SFP+ Module SFP/SFP+ Slot SFP/SFP+ Module

12. 3.3 Console Portp. 26

    CLI (Command Line Interface) enables you to manage the switch, thus you can load the CLI after connecting the PCs or Terminals to the console port on the…

13. 3.4 Verify Installationp. 27

    After completing the installation, verify the following items: • There should be 5 to 10 cm of clearance around the device for ventilation and make sure the…

14. 3.5 Power Onp. 28

    Plug the female connector of the provided power cord into the power socket of the device and plug the positive connector into a power outlet as the following…

15. 3.6 Initializationp. 28

    After the device is powered on, it begins the Power-On Self-Test. A series of tests run automatically to ensure the device functions properly. During this…

16. Chapter 4 Configurationp. 29

    4.1 Configuration Overview The switch supports two configuration options: • Standalone Mode: Configure and manage the switch singly. • Controller Mode…

17. 4.1 Configuration Overviewp. 29

    The switch supports two configuration options: • Standalone Mode: Configure and manage the switch singly. • Controller Mode: Configure and manage the network…

18. 4.2 Standalone Modep. 29

    In Standalone Mode, use a computer to configure and manage the switch using GUI (Graphical User Interface) or CLI (command-line interface). Figure 4-1 Topology…

19. 4.3 Controller Modep. 30

    Controller Mode applies to the large scale network with mass devices. All devices can be centrally configured and monitored via Omada Hardware Controller or…

20. Appendix A Troubleshootingp. 33

    Q1. What could I do if I forgot the username and password of the switch? 1. Connect the console port of the PC to the console port of the switch and open a…

21. Appendix B Specificationsp. 34

    Specifications for Switches with RJ45 Ports and SFP/SFP+ Slots Item Content Standards IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3z, IEEE…