Loading error codes…
Loading error codes…
Air conditioners
38 codes from the official GE PH50S10BNY user manual, in the manual’s own words.
Lower Heating Element Failure Call Service to replace respective heating element
Page 32 of the manual →Compressor Failure or Discharge temp. too high Call service
Page 32 of the manual →Fan Failure Call service F16*, F17 No Hot Water - Mixing Valve Outlet DC TCO Tripped on EMV models or missing jumper wire on non-EMV models Call Service F18*, F63* Mixing Valve Failure Call service
Page 32 of the manual →Runaway Heat Source Call Service
Page 32 of the manual →Tank Temperature (T1) Failure open/short Call Service to replace sensor
Page 32 of the manual →Tank Temperature (T2) Failure open/short Call Service to replace sensor
Page 32 of the manual →Tank Temperature, (T1 or T2) Failure Call Service to replace required sensor
Page 32 of the manual →T3a Sensor (Evap inlet temperature) Failure Call service
Page 32 of the manual →T3b Sensor (Evap outlet temperature) Failure Call service
Page 32 of the manual →T4 Sensor (Compressor outlet) Failure Call service
Page 32 of the manual →T5 Sensor (ambient temperature) Failure Call service F38* Mixing Valve Outlet Temperature (T6) Failure Call Service to replace required sensor F39* Mixing Valve Cold Inlet Temperature (T7) Failure Call Service to replace required sensor F41# Sensing Anode miswired or Empty Tank or Anode Rod Wired Incorrectly Confirm wire is connected to sensing anode terminal. Call Service otherwise.
Page 32 of the manual →Water leak detected (from Leak Detect Module) Inspect for water leak and repair, as required
Page 32 of the manual →Condensate Sensor Failure Call Service to replace required sensor
Page 32 of the manual →Evaporator Not Frost Free. Probable refrigerant leak or Evaporator Not Defrosting Call service
Page 32 of the manual →Seal System Vapor Lock Fault Call service
Page 32 of the manual →T5 Ambient Temperature Check Technician service data - Ambient beyond Heat Pump operating conditions
Page 32 of the manual →Control Board - high temperature fault Call service
Page 32 of the manual →Inverter Fault Call service
Page 32 of the manual →Inverter Software Fault Call service
Page 32 of the manual →Compressor Discharge Temperature Low Call service
Page 32 of the manual →Superheat too low. Possible refrigerant leak. Call service
Page 32 of the manual →Electronic Expansion Valve Out of Range. Probable refrigerant leak. Call service
Page 32 of the manual →Electronic Expansion Valve Out of Range. Probable refrigerant leak; or Refrigerant Leak Test. Probable refrigerant leak. Call service
Page 32 of the manual →Concurrent Load High Current Call service
Page 32 of the manual →AC detection Failure Call Service to confirm wiring is correct
Page 32 of the manual →Tank water temperature is too hot Should self correct
Page 32 of the manual →Incoming water too hot Reduce any preheat of inlet water or call for Service F70# Anode Depleted Call Service to replace sensing anode (see anode replacement section in manual).
Page 32 of the manual →Filter is dirty. If fault repeats after clearing, probable refrigerant leak. Clean Filter. See page 13
Page 32 of the manual →Dry Tank Fault Confirm water in tank. See page 25.
Page 32 of the manual →Voltage too low at power up. Call Service for probable miswire. See page 26.
Page 32 of the manual →Stuck Key Failure Call Service to diagnose and repair
Page 32 of the manual →Leak Sensor detected water Determine source of water leak and correct. Reset shut-off valve, if equipped (see page 13). Call plumber to resolve, otherwise.
Page 32 of the manual →Leak Sensor Battery is low Replace Leak Sensor Battery
Page 32 of the manual →E2 module unplugged or damaged Call Service to diagnose and repair F91 or F92 DataFlash Fault Cycle Power to correct fault after service
Page 32 of the manual →No Personality detected in control board Call Service
Page 32 of the manual →WiFi Board Failure (WiFi icon dark) Call Service to diagnose and repair
Page 32 of the manual →CTA Communication module software fault Call Service
Page 32 of the manual →CTA module disconnected or low battery Reconnect CTA module or replace battery * Applies to models with integrated mixing valve # Applies to models with sensing anode
Page 32 of the manual →Code not listed or still showing? See all GE PF40S10FPY manuals or contact GE service.